answersLogoWhite

0


Best Answer
Copy

There should be three wires attached to back of the alternator of a 66. You should have a black wire with a red stripe hooked to the GRD post, a black wire with a yellow stripe hooked to the BAT post and a white wire hooked to the FLD post. The black wire with the red stripe is the ground and splits off with one end bolting to the engine block on the same bolt that holds the negative battery cable to the block, the black wire with the yellow stripe goes to the hot side of the starter solenoid, and the white wire goes over to the F post on the voltage regulator.

User Avatar

Wiki User

โˆ™ 2010-02-11 14:49:16
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How many wires are connected to alternator on 1966 mustang which color goes where?
Write your answer...
Submit

Related Questions

What color of two wires connected to the IAT sensor on a 2001 v6 mustang?

grey and grey/red (pin1&6)


Where is the alternator on a 1990 Chevy pickup?

The alternator should be on the front of the motor with a belt on the pulley and wires connected to the back of it that can be removed.


How do you connect an alternator to a ford 460 boat motor?

we have a 460 ford in our jet drive boat. recently we have replaced the fotor and the alternator is not charging we are not sure if it is connected properly. It is currently connected with two wires. What Do you recommend?


How many wires go to an alternator?

Number of Wires to an AlternatorThat depends on:the alternator,the wiring system in the vehicle


Need a wiring diagram for 1986 Nissan truck alternator?

I unhooked wires on alternator but did not mark wires


How do you remove the wires from the alternator on a 1997 Toyota tercel?

how do you take the wires from the alternator on a 1997 Toyota Tercel


Remove and replace alternator on Chrysler cirrus?

disconnect the battery. Remove the alternator belt then disconnect the wires. Unbolt the alternator and remove. Bolt the new alternator in then connect the wires, belt, and battery.


How do you connect an oven range cord to the unit when the wires are not color-coded?

It is important to only connect the oven range cord to the unit when the wires are color-coded. This is because if these wires are not correctly connected they may lead to the destruction of the oven.


How telephone wires connected?

I'll take that as "How are telephone wires connected?" but it's still unclear what you want to know. Telephone wires are connected just as any other wires are connected. By screw connections, by soldering, by crimping.


Where do the wires go on a Vauxhall alternator?

from the back of the alternator to the dash to the battery


What are computer components that are connected by wires called?

Peripherals are computer components that are connected by wires.


Will a 1987 mustang wiring harness work in a 1986 mustang?

it will not work the wires and connectot are different


Where is the fusible link for a 1988 jeep wagoneer alternator?

In the engine compartment, passenger side, on top of the wheel well hump closer to the firewall is where it ends, follow the wires coming off of the alternator, you will have to remove the wires from the wire loom, the wire will be connected with a thick rubber insulation on either side of the fusible link(the words 'fusible link' will be printed on the side of the fusible link wire) then it has an eye end and is connected to a single connector panel with a few other wires this is all on the wheel well.


Each of the components connected by wires in a network is called a?

Each component in a network connected by wires is called a terminal. Components in a network that are not connected by wires, such as in a shared Wi-Fi connection are also called terminals.


Wiring diagrams for 1982 Datsun?

alternator wires


What color are the 2 wires connected to the iat sensor on 2006 grand Prix V6?

the tan wire and the blk (D,and E)


How do you replace alternator on 97 cutlass 3.1?

Disconnect the battery negative. Loosen the belt and remove it from the alternator pulley. Disconnect all wires from the alternator. Unbolt the alternator from the bracket. Remove the alternator.


In a 1992 Chevy Beretta alternator how many wires should be connected?

There should be one female plug-in and one separate hot wire that is hot anytime the battery is hooked up.


Why alternator not charging on 1996 jimmy?

Make sure that all wires are connected properly on the correct connections. Make sure that the battery connections are clean and tight. This may help with the problem.


Why does 1994 chev pickup backfires?

Spark Plug wires connected incorrectly, or engine is out of time.Spark Plug wires connected incorrectly, or engine is out of time.


1998 mustang gt wiring?

Yes! they have lots of wires.


Where do the alternator wires go on a 1986 Nissan pickup?

need diagram for 1986 Nissan truck alternator


How do you replace the alternator on a 1995 Ford Aspire?

1. The first thing that you need to do is to disconnect the two wires that are connected to the back of the alternator. 2. Loosen and remove the upper bolt for the adjustment on the alternator. 3. Loosen the lower alternator bolt so that you can take the belt off of the alternator. 4. Move alternator forward so that you can remove the belt. 5. Take the lower bolt out and remove alternator from below. 6. To reinstall repeat steps 1 throw 5 in reverse.


True or false-computers are connected with a network of wires on the internet?

Most are connected by wires, some are connected by a wireless connector ('Dongle'). Two of my friends have wireless dongles.


Remove and replace alternator on a 71 cucda 440?

unbolt it, take the belt off, take the wires off the alternator and replace with new alternator.