answersLogoWhite

0

so that the incoming generator will not act as load but rather a source that can synch in less time

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Electrical Engineering

What size breaker can you use on a 7500watt generator?

Depends on the wire size you are using. If the generator breaker is a 30 amp then install a 30 amp breaker.


What is the function of synchronizing lamps?

The light system of paralleling generators has lamps hooked in series and connected between the hot lead of the lead generator and the hot lead of the lag generator. When one generator is running faster than the other one, the lights will blink off and on as the generators come in and out of phase with each other. Adjusting the throttle of the lag generator and bringing it closer to synchronise speed will cause the lights will start to pulsate slower and slower until they go off for a period of seconds and then on for a period of seconds. At this point the two generators are electrically paralleled. Count the time between on off on of the lights. At half the off time (zero voltage) throw the switch and the generators will lock together, the two generators will be running in parallel with each other. Manually to keep them paralleled requires a bit of work, as the faster generator will try and take the load and motor the other one. This is where a governor is a great asset. If the generators are tied together out of phase two things could happen. The least problematic would be the generators breaker will trip. The second and most dangerous is if the lag generator is just a little bit out of phase when the switch is thrown, then the generator will be jerked into phase lock as momentary heavy current flows between the two generators. The sudden loading of the generator has been known to break crankshafts of the engine driving it.


How do you flash the field of a generator?

start generator, plug in variable speed drill, set drill to forward, squeeze trigger, quickly spin drill in reverse by hand. be sure generator main breaker is on.


An alternator could be severely damaged mechanically in attempting to sychronize it with the power line under what two conditions could this happen?

I'm not sure this qualifies as two different conditions, they are both similar.If the generator is more than a few degrees out of phase.If the generator phase angle is leading at the exact moment it closes to the bus.Explanation for #2: When manually syncing a generator, it is quite difficult to close the breaker at exactly 0 degrees, which is, of course, the desired outcome. If you close the breaker with the generator lagging a few degrees, the bus voltage (utility or other generator) will attempt to speed up the generator as if it were starting a motor.No harm done if the phase difference is just a few degrees. If, on the other hand, you close the breaker while the generator is leading, the bus voltage attempts to 'yank' the generator back to where it belongs, like a brake. If the phase difference is great enough, this can shear driveplates and even break crankshafts!The operator, then, shoots for zero to a couple degrees lagging when the breaker closes.


If you have a circuit breaker box containing 650 amps of circuit breakers it is 3 phase 480 volts what size kva generator do you need?

The question isn't the number of amps total on your branch circuits, but rather, what your MAIN breaker(s) are rated at. This will determine what size of generator you will need. And be certain that the generator is 3-phase. <<>> The formula you are looking for is Amps = kva x 1000/1.73 x voltage.

Related Questions

What direction must the synchroscope be travelling when the breaker is closed?

The synchroscope must be moving clockwise to indicate that the generator frequency is slightly higher than the system frequency. This ensures that when the breaker is closed, the two frequencies will synchronize properly.


How do you synchronized generator 1 to which is running to generator 2?

First, you must make sure that your Generator is in phase and with the same frequency.. When your Generators is the same as what I've mentioned above. Then you are ready to synchronize your Gen. Turn on the synchroscope pointing on the incoming Generator. Observe the pointer or arrow in the synchroscope, it must be turning in fast direction..adjust the speed of turn of the pointer by adjusting the governor knob..lastly close the circuit breaker(ACB), when the pointer points on 00 degree of the synchroscope, adjust the load sharing using the governor knob..


How do you wire a generator to a breaker box?

To wire a generator to a breaker box, you need to install a transfer switch between the generator and the breaker box. The transfer switch ensures that power from the generator is safely and properly connected to the breaker box, allowing you to switch between generator power and utility power when needed. It is important to follow the manufacturer's instructions and consult a professional electrician to ensure proper installation and safety.


What is a generator breaker?

The generator circuit breaker or gcb is a circuit breaker which is connected with the generator . Whenever there is a fault in the generator the circuit breaker trips and disconnects the generator from operation thus it helps the place from a serious accident etc..


How do I wire a generator to a breaker box?

To wire a generator to a breaker box, you need to install a transfer switch between the generator and the breaker box. The transfer switch ensures that power from the generator is safely and properly connected to the breaker box during a power outage. It is important to follow the manufacturer's instructions and consult a professional electrician to ensure the wiring is done correctly and safely.


What size breaker can you use on a 7500watt generator?

Depends on the wire size you are using. If the generator breaker is a 30 amp then install a 30 amp breaker.


Can a generator be motored simply by closing generator breaker to energized bus?

No.


What is 52g?

Generator Breaker Status


How does a generator breaker interlock work to ensure safe operation of a generator and prevent backfeeding into the utility grid?

A generator breaker interlock is a safety device that prevents a generator from backfeeding into the utility grid. It works by physically preventing the generator breaker and the main utility breaker from being turned on at the same time. This ensures that the generator is only supplying power to the home or building it is connected to, and not sending electricity back into the grid, which can be dangerous for utility workers.


How is a Load applied to a ac generator?

The load conductor is connected to the load side of the generator breaker. Once the generator is up to speed the load breaker is closed and the voltage is then applied to the load.


How can I properly connect a generator hookup to a breaker box?

To properly connect a generator hookup to a breaker box, you should install a transfer switch. This switch allows you to safely switch between utility power and generator power. Make sure to follow the manufacturer's instructions and hire a qualified electrician if needed.


What is 52G protection?

Generator Breaker Status