Yes the ballast and starter are the same
you can run halide in hps, but not hps in halide.
No, the ballast has to be matched to the lamp. 250 watt ballast, 250 watt lamp. Also be sure to match the lamp type to the proper ballast even though the wattage is the same. HPS ballast to HPS lamp, Metal halide ballast to metal halide lamp and mercury vapour lamp to mercury vapour ballast.
The abbreviations are CFL - Compact Fluorescent Lamp, MHL - Metal Halide Lamp, HPMV - High Pressure Mercury Vapor, and one more is HPS - High Pressure Sodium lamp
When you want to use a MH bulb in an HPS ballast you must use a conversion bulb. It must be the same wattage as the HPS bulb
Yes, you can run a 400-watt metal halide (MH) bulb in a 600-watt high-pressure sodium (HPS) fixture, but you need to ensure that the ballast is compatible with the MH bulb. Using a 400-watt MH bulb in a 600-watt ballast may lead to reduced efficiency, as the ballast will deliver more power than the bulb requires. It's essential to check the ballast type and ensure that it can operate both bulb types safely. If not compatible, it's best to use the appropriate ballast for the MH bulb to avoid damaging the bulb or the fixture.
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
It will not. A HPS lamp has a much lower ignition current than a MH lamp. There are lamps called "multi-vapor' "MVH" that will work in a MH luminaire. you can run metal halide in hps but not hps in halides.
No, the ballast has to be matched to the lamp. 250 watt ballast, 250 watt lamp. Also be sure to match the lamp type to the proper ballast even though the wattage is the same. HPS ballast to HPS lamp, Metal halide ballast to metal halide lamp and mercury vapour lamp to mercury vapour ballast.
To grow marijuana in the vegetative stage. HPS for flowering
I actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem. So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb. As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
The abbreviations are CFL - Compact Fluorescent Lamp, MHL - Metal Halide Lamp, HPMV - High Pressure Mercury Vapor, and one more is HPS - High Pressure Sodium lamp
When you want to use a MH bulb in an HPS ballast you must use a conversion bulb. It must be the same wattage as the HPS bulb
yes
Metal halide lights are a type of high-intensity discharge light. They're frequently used as grow lights for plants in conjunction with HPS (high pressure sodium) lights. MH lights are better for the earlier vegetative growth stages.
No, you cannot use a 1000 watt HPS (high-pressure sodium) lamp without a ballast. The ballast is essential for regulating the electrical current flowing through the lamp, which is necessary for it to operate properly and prevent damage. Trying to operate a 1000 watt HPS lamp without a ballast can result in the lamp not lighting up or malfunctioning.
A typical 400-watt high-pressure sodium (HPS) lamp has a running wattage of around 450-480 watts. This higher operating wattage accounts for the power draw required to start and maintain the lamp's operation. It is essential to consider this when calculating power consumption for lighting setups.
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
LEDs do not contain the toxic metals found in HPS (High Pressure Sodium) and MH (Metal Halide) lamps! That's less hazardous waste to deal with, allowing for easier recycling and safer disposal. for more info and lights come to tacticallight.com