answersLogoWhite

0

Subjects
>
Engineering & Technology
>
Electrical Engineering

Electrical Engineering

Focus on the study and application of electricity, electronics, and electromagnetism. This field is integral to systems ranging from household appliances to telecommunications.

16.3k
Questions
Q: What is the unit of measurement of inductive reactance
1 answer
Q: What is meant by PVC cables
1 answer
Q: The purpose of a Cobra inverter is what
1 answer
Q: Step by step procedure for creating pso program in matlab.Im trying to find optimal placement of svc in power system.also provide links where you can learn it
1 answer
Q: Why in center tapped transformer tap ground is used
1 answer
Q: Will a step up transformer from 208 to 480 save on power bill
1 answer
Q: Which of these could not be used to replace a wire in a circuit
2 answers
Q: How do you select field rheostat range for dc motor
1 answer
Q: What happens to electrical in a resistor
1 answer
Q: What is the operational frequency of half wave dipole antenna
1 answer
Q: What is a 100 amp 208 single phase
1 answer
Q: What are ten object in your home that use semiconductors
1 answer
Q: Why Ac voltage supply in your home has a magnitude 220V and frequency 50 Hz
1 answer
Q: Why it is called as delay circuit
1 answer
Q: How many amps does a 1 hp electric motor pull under a load
2 answers
Q: How do you slipring motor is convert to inducton motor
1 answer
Q: How do you use a multimeter to measure the current in a lemon
1 answer
Q: Ac voltage applied across a load resistance produce alternating current
1 answer
Q: What is the actual measured resistance of the circuit if the Vom is set to the R x 100 range and the meter face reads 22.5
1 answer
Q: Why the armature rheostat of dc is motor kept at maximum resistance position
2 answers
Q: What will be out put wattage on convertion of 200 watt 12 volt DC to AC through inverter
1 answer
Q: How do you use ohm's law to determine the current flowing through a 45 ohm resistor at 1.4 amps
1 answer
Q: How much current will pass through r3
1 answer
Q: Can an AND gate be formed by using two OR gates
2 answers
Q: When does Carrier Signal occur
1 answer
Q: When will a negative feedback amplifier circuit be unstable
1 answer
Q: Are pyranol capacitors dangerous
1 answer
Q: Why base in grounded in common emitter transistor as amplifier
1 answer
Q: Why Y phase is high in YNyn0 when doing magnetic balance test
1 answer
Q: What is the total current if a 60 ohm 40 ohm and 20 ohm resistors are all three connected in series across a 120 VAC source
1 answer
Q: What is the efficiency of a 172.5Watt heater which draws 2A from a domestic supply
1 answer
Q: What are convectional and non convectional methods of speed control of a induction motor
1 answer
Q: What happens when more than rated voltage applied to transformer
1 answer
Q: What is the purpose for generator synchronising
1 answer
Q: Why you use pull up resistor in microcontroller 8051
2 answers
Q: What are the characteristics of fixed bias
1 answer
Q: What is the transmission time of a packet sent by a station if the length of the packer is 1 million bytes and the bandwidth of the channel is 200 Kbps
1 answer
Q: When a light is on it is part of a scolde circuit
6 answers
Q: Where a 110v mains is not available on sidewhat device is commonlyused to provide the required reduced low voltage
1 answer
Q: What is an 8 pin ic socket
1 answer
Q: Why the heat sink is always used in power electronics converters
1 answer
Q: What is power cable size for 1 kw 1 phase motor over 500 meters
1 answer
Q: What is a backlight inverter
1 answer
Q: How much current will 5 kva ups draws while charging
1 answer
Q: What is the Formula to know about of dc cable size in mm
1 answer
Q: Why is common emitter is greater than common collector
1 answer
Q: How does emitter current is equal to base current and collector current
1 answer
Q: When you pass the digital signal through a transmission medium the output will be a digital signal without any losss
2 answers
Q: How are series circuits utilized in a schematic diagram
1 answer
Q: Two lamps A and B are rated 60W 220V and 100W 220V respectively so why does the answer say that when connected in parallal bulb A is brighter
1 answer
Previous266267268269270271272273274275Next
Trending Questions
VOM has the higher loading effect? Why torque is not zero in no-load speed? What is the advantage of Programmable logic device over microcontroller? What does the arrow in bipolar junction transistor symbol represent? How do you do for phase sequence protection at three phase motor operation? The electrical power dissipated by a resistance R is? How does electrical resistance change the current in a circuit? 208 volt 12 amps versus 277 volt 6 amps? What is the equivalent for D5023 transistor? Which type of filter is independent of load why? A ring counter consisting of five flip-flops will have? What is value of R56K resistor? Write down the advantage of 2-wattmeter method instead of 3-wattmeter method for measuring ac power? Why pn junction is neutral? What is electrical impendance? What diode is used as voltage controlled capacitor? Who invented electromagnetic generator? What is the full form of OHMS in envelope? What is the effect of inductive load on a single phase full wave bridge rectifier? Which filter is practically preferred to get pure DC output?

Resources

Leaderboard All Tags Unanswered

Top Categories

Algebra Chemistry Biology World History English Language Arts Psychology Computer Science Economics

Product

Community Guidelines Honor Code Flashcard Maker Study Guides Math Solver FAQ

Company

About Us Contact Us Terms of Service Privacy Policy Disclaimer Cookie Policy IP Issues
Answers Logo
Copyright ©2026 Infospace Holdings LLC, A System1 Company. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.