answersLogoWhite

0

I did it the easy way. I bought a BRASS compression coupling (Plumbing supply House) , Plastic won't take the tightening required for a pressure seal.

I just hack sawed off the "tee" part and connected the 2 straight sections with the Brass coupler. I have replaced my Well Saver LPT20 twice over the years with this technique. They tend to rust out underneath at the weld after several years.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

How much vacuum is created by centrifugal pump during empty out the tank?

If we install centrifugal pump to transfer liquid from tank,after empty out the tank pump is continiously running,then how much vacuum is created in tank?


What if your toilet does not have a tank ball or flapper?

Mine has neither and it works perfectly I install this type all the time


Can you shut off the cold water intake to hot water tank to stop a leak not in hot water tank?

Yes, but there still is all the water stored in the tank plus the water stored in the existing hot water lines throughout your home that will eventually leak out.If you intend to install a hot water heater (HWH) yourself and you do not have valves to isolate the existing plumbing then turn off your main water supply, drain the water from your home using the lowest level sink, then attach a hose to the bottom of the HWH and drain the tank. When you install the new HWH install new shutoff valves. (Hint: Check with your local city plumbing and see if an expansion tank is required.)


Does the Ontario plumbing code require install of an anti-scald device for domestic hot water?

Yes. If you change any fixture or hot water tank you must install a valve that limits the hot water delivery at the new fixture to 48C. If you change the hot water tank you must either put a valve on all fixtures except the diswasher and clothes washer or add a mixing vavle on the output of the tank.


Can you install a water heater on its side?

No. Gas fired the flame wouldn't touch the tank and on an electric, the thermostat would not work correctly. Cold water is meant to be at the bottom of the tank until it is heated and then taken out of the top.

Related Questions

How do you install a diesel auxilary fuel tank?

depends what you want to install the tank in if it is in a pickup, there are easy to install tanks available that sit in bed of truck some also have tool boxes built in


How do you install fuel pump on 2002 Nissan maxima?

Remove fuel tank, replace pump from top of tank, re-install. Change the fuel filter while your at it!


How do you install a fuel pump on a 1989 Pontiac TransAm?

The gas tank has to come down as the pump is in the tank.


How do you install fuel pump on 2002 Lincoln?

It is you gas tank; empty all gas out, then drop tank.


How do I install a pressure tank?

To install a pressure tank, first turn off the power to the pump. Then, connect the tank to the water supply line and ensure it is level. Next, adjust the air pressure in the tank to the recommended level. Finally, turn the power back on and check for leaks.


How much does it cost to install a septic tank?

The cost to install a septic tank can vary depending on factors like size, location, and soil conditions, but it typically ranges from 3,000 to 9,000.


How much money will I have to invest if I were to buy all the material to install it myself?

You will not be able to install your own septic tank.


How do you install in tank gas pumps?

Unless there is an access hole in the rear area of vehicle you have to drop the fuel tank- there is access at the top of the tank for replacement


How do you install a gas tank on 69 Chevelle?

hoist up into place and tighten down the 2 gas tank straps to hold the tank in place, hook up the hot wire to the fuel sending unit and ground wire to the car body and then install the fuel line to the tank and your done.


How do I install an expansion tank in my plumbing system?

To install an expansion tank in your plumbing system, first turn off the water supply. Locate a suitable spot near the water heater to install the tank. Connect the tank to the cold water line using a tee fitting. Make sure to follow the manufacturer's instructions for proper installation. Once the tank is securely in place, turn the water supply back on and check for any leaks.


How do you install fuel tank on 1995 f-350 turbo diesel?

which tank you want to install? front or rear. 1995 f350s have 2 tanks and a switch on dash to swap from front to rear.


How do you install a hot water recirculating line to accomadate the most remote fixtures.?

Install line from the outlet of the tank and run line to the last fixture and bring it back to the bottom of tank with a pump