0
Yes, you can wire a 6 ohm sub with a 4 ohm sub to the same amplifier, but you need to verify that the amplifier can handle the resulting impedance of 2.4 ohms - many cannot, and could be destroyed. Also, realize that the power in the 4 ohm sub will be greater than the power in the 6 ohm sub.
What else can I help you with?
Can you wire a 4 ohm 500 watt sub woofer in parallel with a 4 ohm resistor to get 300 watts out of your 75 x 2 bridged amp would this effect sound quality what wattage of resistor?
This would have 2 effects:Cause an impedance mismatch between the amp and the speaker.Draw more current from the amp, possibly overloading & damaging it.Neither is desirable.
What does sub-floor mean?
under a foundation of a sub.
How do you write H2O in HTML code?
To write the elemental definition of water (H20) in HTML, use the <sub></sub> element to surround the 2. SUB designates a particular portion of text as subscript. So... <p>H<sub>2</sub>O</p> Will give results similar to: H2O
What are subtractor op-amplifier?
Subtractor :In Electronics Subtractor is a Combinatorial circuit which is used to Subtract two Binary Numbers, x & y.Half Subtractor :Half Subtractor is a circuit which is used to Subtract the two bit Binary Numbers.Full Subtractor :Full Subtractor is a circuit which is used to Subtract the Two Bit Binary Numbers and a 1 borrowed from Last Lower significant stage.Hope this answer will help you.....Remember In your Prayers.
What happens if we sample the signal at sampling frequency nearer to signal frequency?
If you sample at more than the Nyquist frequency (one half the signal frequency) you introduce an aliasing distortion, seen as sub harmonics.
Set up 2 4 ohm sub to 2 ohm?
If you are trying to pump a 2.4 ohm sub with a 2 ohm rated amplifier you should be fine. The rating on the amplifier is the least resistance it should have on its load. Anything less than 2 ohms would fry your amp.
Can you have a 2 ohm sub with a 4 ohm sub?
Yes, you can have a 2 ohm subwoofer and a 4 ohm subwoofer in the same system. However, it is important to match the impedance to avoid damaging your amplifier. You can wire them in series or parallel to achieve a compatible overall impedance for your amplifier.
Your Amplifier for your 600 watt sub is cutting out The peak in the amp is 600 watts How do you get it to stop cutting out?
you ohm load is too low. raise the ohm load or buy an amp that is stable at the ohm level of the sub.
Can you hook up a 4ohms sub and a 2ohms sub to the same amplifier?
ONLY if your amp can pull a 2 ohm load! Which is vary few but your more expensive amp can pull 1/2 ohm load
Can you wire a dvc 4 ohm sub woofer and a svc 8 ohm sub woofer together on a 4 ohm amp?
Sorry, but there is really no 4 ohm amplifier. We use only voltage bridging. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
I have a Sub hooked up to my sony home stereo and my 12 inch sub isint pounding like it should there is no bass changer on the stero so can you manualy turn up the bass on the sub somehow?
You need to get a better amplifier for your sub.
How do you wire dvc 4 ohm sub to 4 ohm amp?
There is really no amplifier on the market which has an output impedance of 4 ohms. The impedance of an amplifier is always less than 0.5 ohms. We do not use matching, we use bridging when we connect the amplifier to the loudspeaker. Scroll down to related links and look at "Interconnection of two audio units".
2 ohm sub woofer to 4 ohm amp?
That could work, because there does no 4 ohm amplifier exist. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout << Zin. The damping factor Df = Zin / Zout tells you what Zout is. Zout = Zin/Df. If the damping factor Df = 200 and the loudspeaker impedance is Zin = 4 ohms, the output impedance of the amplifier is Zout = 4 / 200 = 0.02 ohms. You see, there is no "4 ohm amplifier" with a 4 ohm output. Scroll down to related links and look at "Voltage Bridging - Zout < Zin".
Can you hook your 2-ohm sub to your 4-ohm amp If so how?
That could work, because there does no 4 ohm amplifier exist. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout << Zin. The damping factor Df = Zin / Zout tells you what Zout is. Zout = Zin/Df. If the damping factor Df = 200 and the loudspeaker impedance is Zin = 4 ohms, the output impedance of the amplifier is Zout = 4 / 200 = 0.02 ohms. You see, there is no "4 ohm amplifier" with a 4 ohm output. Scroll down to related links and look at "Voltage Bridging - Zout < Zin".
1000watt rms 2 ohm 15inch subwoofer what would be the best wattage amplifier to pair with this and would it have to be 2 ohm aswell?
is it duel 2 ohm or duel 4 ohm or just a singel 2 ohm sub??? you can run anything from a 1 ohm amp to a 2 ohm amp just depending if you want to add another sub later if your wanting to add 1 later get 1 big enough to run 2 subs so you wount be wasting your money on sumthing you dont need say 5 months from now
Where is the amplifier in a 97 Ford Expedition not the sub amplifier?
How to apply the amplifier to my expedition
Will a 4 ohm 800 watt sub woofer work well with a 8 ohm 800 watt amplifier?
Sorry, but there is no 8 ohm amplifier on the market, when you mean the output impedance. The impedance is always 0.5 ohms or less. We don't use impedance matching, we use voltage bridging. Scroll down to related links and look at "Interconnection of two audio units - power amplifier and passive loudspeaker".sorry yourself any power amplifier has an impedance matching characteristic's He is asking would it work my answer is yes but not as efficient as originally designed
