Yes, you can use both, but watts is more useful; it provides the total amount of power the generator can output.
Unlike DC in AC Power is the Product of Voltage*Current*Power FactorP = V*I*PFIn the above expression power factor is a variable quantity which can be different for different circuit hance does not allow you to specify ratings in KW rather then KVA.
KV is the unit used for VOLTAGE measurement. AC power is complex quantity that is it has both magnitude and direction and hence has two parts real part and imaginary part. complex power is measured in KVA (kilo volts amps) real part (active component ) is measured in KW (kilo watts) imaginary part (reactive component) is measured in KVAR (kilo volts amps reactive)
It simply the product of r.m.s current through that conductor and r.m.s voltage across the conductor and the neutral/ground. We can measure the voltage with help of voltmeter and current with help of ammeter.Both these meter measure these quantity in r.m.s mode.
There is appoximately zero kVA in 14amp, .5 volt AC.
The volt ampere is a measurement of apparent power, while the watt is a measurement of true power. Apparent power is simply the product of voltage and current; the output of a transformer, therefore, is the product of its rated secondary voltage and its rated secondary current -i.e. the apparent power of the transformer. The power supplied, in watts, is determined by the power factor of the load, so there is little point in rating a transformer in watts, as the designer has no means of knowing the power factor of the load it is to supply.
Unlike DC in AC Power is the Product of Voltage*Current*Power FactorP = V*I*PFIn the above expression power factor is a variable quantity which can be different for different circuit hance does not allow you to specify ratings in KW rather then KVA.
Transformers, like inductors can only handle a specific amount of voltage and current before overheating, with AC or DC input. AC 'real' power delivery from a transformer is measured in kilowatts (kW) which is identical to KVA when "Power factor = 1". In the extreme, with "Power factor =0", a transformer could be fully loaded in terms of KVA, while supply zero 'real' power (kW).
kVA is kilo-volt-ampere, which is 1000 x volt x ampere. kVA is the unit of apparent power in AC circuits.
To convert AC tonnage to kVA and kW, use the following formulas: For kVA: kVA = (tonnage x 3.517) For kW: kW = (tonnage x 3.517 x power factor). Remember to consider the power factor of the system when converting from tonnage to kVA and kW.
KV is the unit used for VOLTAGE measurement. AC power is complex quantity that is it has both magnitude and direction and hence has two parts real part and imaginary part. complex power is measured in KVA (kilo volts amps) real part (active component ) is measured in KW (kilo watts) imaginary part (reactive component) is measured in KVAR (kilo volts amps reactive)
KVA is very simple, it is the Volts x Amps of an AC circuit in units of 1000. For a single phase AC circuit VA = E x I. KVA = (ExI)/1000 So if you have 120 VAC and 15 A then: VA = 120 x 15 = 1800; KVA = 1800/1000 = 1.8 For 3 phase circuits we need to add the square of 3 (= 1.732) as a factor. VA = 1.732 x E x I and KVA = (1.732 x E x I)/1000 So if you have 480 VAC and 23 A then: VA = 1.732 x 480 x 23 = 19,121; KVA = 19,121/1000 = 19.1 Note that KVA is higher than KW (true power) in circuits that are not purely resistive. The vector difference of the two is "Power factor".
A 1-ton AC can melt a ton of ice in 24 hours. The power needed is theoretically 3517 Watts so allowing for power factor and efficiency you would need a 7 kVA generator.
a VA is basically equivalent to a watt for most purposes so a KVA being 1000 VA, a KVA is basically 1000 W.However, 1 KVA = 1KW only holds true for resistive loads. If an AC power supply is running a motor or other very inductive load, KVA can be significantly higher than the power being used by the motor.The theory and mathematics of inductive loads are too complex to describe here but knowledge of inductive loads on AC supplies is one of the fundamentals of electrical engineering
It simply the product of r.m.s current through that conductor and r.m.s voltage across the conductor and the neutral/ground. We can measure the voltage with help of voltmeter and current with help of ammeter.Both these meter measure these quantity in r.m.s mode.
Inverters and generators are not rated in BTU's (British Thermal Units). They are rated in KVA (Kilovolt amps) and KW's (Kilowatts). These two values are the product of amps times volts. KVA times PF (Power Factor) = KW.
The two main types of generators used to produce electricity are AC (alternating current) generators and DC (direct current) generators. AC generators are commonly used in power plants and homes, while DC generators are typically used in portable devices and certain industrial applications.
AC generators are commonly used to convert mechanical energy into electrical energy for powering various devices and appliances. They are utilized in power plants to produce electricity on a large scale for residential, commercial, and industrial applications. AC generators are also found in portable generators, wind turbines, and some types of vehicles for generating electricity.