answersLogoWhite

0

different microprocessors take different number of states. without knowing processor its not possible to comment.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

How many machine cycles and T-series requires to complete the execute STA 4200H in 8085 microprocessor?

The STA 4200H instruction in the 8085 requires 4 machine cycles and 13 T states to complete its fetch, processing, and execution. Cycle One: Opcode fetch, 3 T states plus one opcode process state. Cycle Two: Opcode address byte 00H fetch, 3 T states Cycle Three: Opcode address byte 42H fetch, 3 T states Cycle Four: Accumulator store, 3 T states. Each cycle will have additional T-Ready states as needed by the READY pin. 13 T states is the minimum. The LDA instruction will also require 13 T states, with the last cycle being a read cycle instead of a write cycle.


How do you write object code for format 2 instruction in sic xe machine?

To write object code for a format 2 instruction in the SIC/XE machine, you need to identify the opcode for the instruction and the registers involved. The object code consists of the 8-bit opcode followed by the 4-bit binary representation of the two registers. The format is typically structured as follows: the first 8 bits for the opcode, the next 4 bits for the first register, and the last 4 bits for the second register. Finally, you concatenate these binary values to produce the final object code.


What are the various phases of an instruction cycle Give the micro operation of fetch and decode phases?

there are 4 phases in instruction cyclefetchdecodeexecutestore


Advantages of microprocessor based system?

There are many different advantages of a microprocessor based system. Some of these include that it only uses 3 components so it is simple to use and install and it will increase your memory.


What are the four task that a CPU performs to process information that has been input by a user?

1)Fetch 2)Decode 3)Execute 4)Store

Related Questions

How many machine cycles and T-series requires to complete the execute STA 4200H in 8085 microprocessor?

The STA 4200H instruction in the 8085 requires 4 machine cycles and 13 T states to complete its fetch, processing, and execution. Cycle One: Opcode fetch, 3 T states plus one opcode process state. Cycle Two: Opcode address byte 00H fetch, 3 T states Cycle Three: Opcode address byte 42H fetch, 3 T states Cycle Four: Accumulator store, 3 T states. Each cycle will have additional T-Ready states as needed by the READY pin. 13 T states is the minimum. The LDA instruction will also require 13 T states, with the last cycle being a read cycle instead of a write cycle.


How many machine cycles requires to complete the execute IN 84H in 8085?

The instruction IN 84H in the 8085 microprocessor requires 5 machine cycles to complete. This includes 1 opcode fetch cycle and 4 memory read cycles. The opcode fetch retrieves the instruction from memory, while the read cycles are used to read the data from the specified input port.


Why in 8085 timigdiagram STA intruction has 13 t states?

The STA instruction in the 8085 has 13 T states, 4 for opcode fetch, 3 for low half immediate address fetch, 3 for high half immediate address fetch, and 3 for data write.


Why call instructions in 8085 takes 18 state during fetch and execute?

4 states for opcode fetch and decode 3 states for each byte to retrieve the target (call) address 3 states for each byte of PC to push on the stack 1 state for each decrement of the stack pointer


How 8085 timing diagram works based on each instruction?

Each instruction requires specific time for the execution of instruction and this time is called instruction cycle. Each instruction cycle consists 1 to 5 machine cycle -- opcode fetch, memory read, memory write, IO read, IO write and each machine cycle consist 3 to 6 T - states. Time required to execute 1 T-state = 1/ operating frequency of 8085 Microprocessor for example operating frequency = 2MHz then time required to execute 1 T-state = 0.5 uSec example: Calculate time required to execute instruction MOV C, A sol: This instruction has one machine cycle i.e. opcode fetch (In any instruction 1st cycle is always opcode fetch and opcode fetch consists 4 to 6 T state depend on the operation of particular instruction) so to execute MOV C, A required 4T states so time required to execute this instruction is 4*0.5usec = 2usec any other queries pls contect: nileshbahadure2000@yahoo.co.in example:Calculate the time required to execute LXI H,2000H sol:Here we have to draw opcode fetch and two memory reads as two bytes 00H and 20H have to be read from memory. i.e, opcode fetch+Memory reads *2(bytes address) =4+3+3 so to execute LXI H,2000H,the required T-states is 10T and time is 10*0.5usec=5usec


How many machine cycle required for the instance like move a b?

The MOV A,B instruction requires 1 machine cycle and 4 T-states, 3 to fetch the opcode, and 1 to decode/execute it.


How many machine cycles in the XCHG instruction?

Summary − So this instruction XCHG requires 1-Byte, 4-Machine Cycles (Opcode Fetch) and 4 T-States for execution as shown in the timing diagram.


How many machine cycle are required in LDA 2050H?

It will require 4 machine cycles, 1.opcode fetch 2.memory read 3. memory read 4. memory write


When and by whom did the world's first microprocessor come into the market?

The question is unclear, but it looks like it meant to ask when the first microprocessor was invented. That was the Intel 4004, invented in 1971. It was the first single chip microprocessor, and the first microprocessor available commercially. The 4004 was a 4 bit processor, with a 12 bit address bus and an 8 bit opcode. Everything was multiplexed, 4 bits at a time, in 8 clock cycles per instruction.


How many different instructions can contain in four bit opcode?

Hi, The equation to find the number of instructions with n-bit opcode is 2^n. If your opcode is n=4, the it's 2^4 which is 16. So with a four bit opcode you can have 16 different instructions. ---- 11 levels


How many machine cycles are required for RET instruction in 8085 microprocessor is?

RET instruction needs 3 machine cycles. One to fetch and decode the instruction(4 T states), and two more machine cycles(i.e. 2*3=6 T states) to read two bytes from the stack(stack is exterior to microprocessor, stack is in R/W memory, so to exchange data with stack needs machine cycles). Thus, RET instruction needs total 3 machine cycles and 10 T-states.


Is Fetch making a season 4?

Fetch is having a season 4! it premieres in the summer or fall! Fetch is having a season 4! it premieres in the summer or fall! Fetch is having a season 4! it premieres in the summer or fall!