answersLogoWhite

0

You can pop them up with a small flat screwdriver. Look carefully and you will see tiny slots. It is just "clicked" in place, no screwing or so.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Where can you buy Renault Kangoo keys Just plastics covers with no remotes or chip?

At a locksmith shop


How do you remove the ignition barrel on a Renault kangoo?

To remove the ignition barrel on a Renault Kangoo, start by disconnecting the vehicle's battery to ensure safety. Next, remove the steering column covers to access the ignition switch. Insert the key and turn it to the accessory position, then locate and press the release pin or tab on the ignition barrel. Finally, gently pull the barrel out of the steering column.


Where is the water coolant sensor on Renault kangoo 1.5 dci?

The water coolant sensor on a Renault Kangoo 1.5 dCi is typically located near the thermostat housing. It is usually positioned on the engine block, close to where the upper radiator hose connects. To access it, you may need to remove some components or covers, depending on the specific model year. Always consult the vehicle’s service manual for precise location and guidance.


How do you remove front dash speakers on a 1989 S10 Blazer?

Begin by removing the dashboard speaker covers on your 1989 Chevy S 10 Blazer. Remove the speaker retaining screws. Remove the speaker wiring harness. The speakers will come out.


How do you replace the dashboard tweeters on a Renault clio?

To replace the dashboard tweeters on a Renault Clio, first gently pry off the tweeter covers using a flathead screwdriver or plastic trim tool to avoid damaging the dashboard. Once the covers are removed, unscrew the old tweeters and disconnect the wiring harness. Connect the new tweeters to the wiring, secure them in place with screws, and reattach the covers. Finally, test the sound to ensure proper installation before reassembling any dislodged dashboard parts.


Where low side port located on Renault Kangoo 2010?

On a 2010 Renault Kangoo, the low side port for the air conditioning system is typically located near the engine bay, specifically on the larger diameter aluminum pipe that connects the compressor to the evaporator. It is usually situated close to the front of the vehicle, near the driver's side. To access it, you may need to remove some covers or components, depending on the specific engine configuration. Always ensure the system is off and depressurized before attempting any work on the AC system.


How do you remove front speaker covers from a 1992 corvette coupe?

The 1992 Chevy Corvette front speaker covers are held in place with two retaining screws. Remove the retaining screws and the speaker covers will come off.


What is the part that covers the speakers?

Speaker grilles.


Removing speakers Chevy blazer 2 door rear?

You will need to remove the rear door speaker covers. The Chevrolet blazer speaker covers are held in place with two retaining screws. Remove the speaker retaining screws. Remove the speaker wiring harness.


Who is the speaker in sandburg's?

In Sandburg's 'Grass,' the speaker in the story is the grass itself. It essentially claims that it is in the grass that covers everything.


How do you rewire speakers in a 1990 GMC suburban?

first you must remove the plastic casing from the rear speakers and remove the dashboard. then disconnect the old speaker wire from the old speakers and tie the new wire to the old wire. at the radio, pull the speaker wires one by one until the new wire reaches you. then splice the new speaker wire to both the radio and the speakers and replace the dash and covers


How remove clio speedo?

To remove the speedometer (speedo) on a Renault Clio, you will first need to locate and access the instrument cluster behind the dashboard. You may need to remove the dashboard trim panels or covers to access the cluster. Once you have access, you can disconnect the wiring harness and mounting bolts securing the speedometer in place. Carefully remove the speedometer from the cluster and replace it with a new one if necessary.