0
What else can I help you with?
What is point B if you touch point C from point A?
Point Z
A point at an end of a segment or a starting point of a ray?
end point
How would you draw a regular pentagon?
*Note that it is assumed you know what the terms diameter, perpendicular, bisect/bisection and intersection mean in relation to geometry. If not, they are explained in the discussion area. To construct a regular pentagon using a compass and ruler (a longer, but more precise method): # Draw a circle in which to inscribe the pentagon and mark the center point O. # Choose a point A on the circle; this will be one vertex of the pentagon. Draw the diameter line through O and A. # Construct a line perpendicular to the line OA passing through O. Mark its intersection with one side of the circle as the point B. # Construct the point C as the midpoint of O and B. # Draw a circle centered at C through the point A. Mark its intersection with the line OB(inside the original circle) as the point D. # Draw a circle centered at A through the point D. Mark its intersections with the original circle as the points E and F. # Draw a circle centered at E through the point A. Mark its other intersection with the original circle as the point G. # Draw a circle centered at F through the point A. Mark its other intersection with the original circle as the point H. # Construct the regular pentagon AEGHF. To construct a regular pentagon using a protractor (less time, but not as accurate): # Make a short line. This will be one side of the pentagon. Label the ends A and B # Place the baseline of the protractor on this line, with the centre at A. # Mark the point of 108o with a dot. # Make another line which starts at A, is the same length as AB and goes towards the dot. # Repeat the use of the protractor on the newest line you have drawn three more times. The final line should meet up with B.
What is the place where a tangent line intersects a circle?
Definition: a tangent is a line that intersects a circle at exactly one point, the point of intersection is the point of contact or the point of tangency. a tangent is a line that intersects a circle at exactly one point, the point of intersection is the (point of contact) or the **point of tangency**.
What does a particular point on a line of a phase diagram represent?
The melting point or boiling point ...................
How is a datum point used?
A datum point is a fixed reference point used in various activities such as surveying, drafting, and engineering to establish a baseline or starting point for measurements and calculations. It helps ensure consistent and accurate results by providing a known reference for all measurements taken within a specific project or task.
Explain how to select and establish a suitable datum the importance of ensuring that marking out is undertaken from the selected datum and the possible effects of working from a different?
To select a suitable datum, consider a stable reference point on the workpiece or surface. Mark the datum clearly and securely. When marking out, ensure all measurements and reference points are taken from this datum to maintain accuracy and consistency. Working from a different datum can lead to incorrect measurements, misalignments, and errors in the final product. It is crucial to avoid this by consistently using the established datum.
How do you select and establish a suitable datum?
Selecting and establishing a suitable Datum is critical, ensure your datum is at a fixed point. Normally a hole/slot. Holes and slots a normally lasor cut, ensuring they are at an extremely high tolorance already. Then reference the slot or hole to another near by slot or hole. Using these selected points will give you accruate points of measurement/datum.
What is the starting point for the measurement of the horizontal lines?
The starting point for the measurement of horizontal lines typically refers to a reference line or baseline from which measurements are taken. This baseline is often established at a specific elevation, such as the ground level or a designated datum point, ensuring consistency in measurements. In architectural or engineering contexts, this could also involve using a level tool to ensure accuracy in alignment.
What is Melbourne's datum point?
burnie
What id difference between data and datum?
Data is the plural, roughly meaning information. Datum is singular and is used someti es to mean a Landmark or starting point, a geodetic Datum point, like in the Grabd Canyon or the Promontory Point in Utah, both recognized landmarks.
What is datum point?
burnie
What is Land Surface Datum?
Land-surface datum is a datum plane that is approximately at land surface at each well. If known, the elevation of the land-surface datum above sea level is given... Datum: any level surface, line, or point used as a reference in measuring elevations.
A primary datum requires how many points of contact?
According to ASME Y14.5, a primary dimensioning datum requires at least 3 points of contact to establish the datum plane. Two points of contact are required for the secondary datum and 1 point of contact is required for the tertiary datum.
When utilizing the DAGR what field automatically displays the waypoint datum?
When utilizing the DAGR, the field that automatically displays the waypoint datum is the "Dat" field, which stands for datum. The datum represents the reference point used to define the location coordinates of the waypoint.
Which baseline runs on any point on the surface to the north pole?
Which baseline runs from any point on earth's surface to the north pole
Which baseline runs from any point on the surface to the north pole?
Which baseline runs from any point on earth's surface to the north pole
