answersLogoWhite

0

The outer diameter of a 2" PVC pipe is approximately 2.375 inches.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

What is the outer diameter of 1/2 PVC pipe?

The outer diameter of 1/2 inch PVC pipe is approximately 0.84 inches.


What is the outside diameter of a 1/2 PVC pipe?

The outside diameter of a 1/2 inch PVC pipe is approximately 0.840 inches.


What are the specifications for a schedule 40 PVC 2 inch pipe?

A schedule 40 PVC 2 inch pipe has an outer diameter of 2.375 inches and a wall thickness of 0.154 inches. It is commonly used for water supply and drainage systems in residential and commercial buildings.


What is the thickness of a pipe that has an outer diameter of 2.5 inches and diameter of 2.1 inches?

Consider going across the width of the pipe: Outer diameter = Thickness + Inner diameter + Thickness so 2*Thickness = Outer diameter - Inner diameter = 2.5 - 2.1 = 0.4 inches and therefore, Thickness = 0.2 inches.


How do you find wall thickness of pipe knowing the outside diameter and inner diameter of pipe?

Outer radius minus inner radius Subtract the inside diameter from the outside diameter, then divide the difference by 2.


How can you calculate the ID of a pipe?

Can you calculate the ID of a pipe when you have the OD to be 10.75" and the wall thickness to be 0.5"Depends on what you know about it. If you have the outer diameter and you know the wall thickness, then ID = OD-2 x wall thickness


What is the diameter of PVC pipe in millimeters?

Electrical trade sizes of PVC conduit are, - 1/2" = 12.5mm, 3/4" = 19mm, 1" = 25mm, 1 1/4" = 32mm, 1 1/2" = 38mm, 2" = 50mm, 3" = 75mm, 4" = 100mm.


How many gallons of water does a one foot 4 inch PVC pipe hold?

Assuming that the INNER DIAMETER of the PVC pipe is 4" (...likely not the case, so you'll need to recalculate for your pipe's dimensions): the volume of the pipe would be calculated as follows: 4" diameter = 2" radius volume_cylinder = Pi*r^2*L; where r = 2" and L = 12" the cylinder therefore has a capacity of 150.8 cubic inches. a gallon of water has the volume of 231 cubic inches. your pipe can hold 0.653 gallons of water. you'll need about 18.38 inch lengths of 4" PVC to hold each gallon of water. again, these calculations rely on the INNER DIAMETER of the pipe being measured at 4" - if this is an outer diameter measurement, the above calculation for the capacity is OVERstated; the 18.38" calculation is UNDERstated.


Max waterflow in 2 inch PVC pipe?

What schedule pipe?


How do you calculate pipe area in to cylinder area?

To calculate the area of a pipe (which is a cylindrical shape), you can use the formula for the cross-sectional area of a cylinder, ( A = \pi r^2 ), where ( r ) is the radius of the pipe. If you have the diameter, you can find the radius by dividing the diameter by 2. For a pipe with a specific outer diameter and thickness, you would use the inner radius to find the area of the flow section.


What is the width of a standard water line PVC pipe?

A standard water line PVC pipe typically has a width (diameter) of either 1/2 inch, 3/4 inch, 1 inch, or 1.5 inches.


What is the best way to connect two sections of PVC pipe with a 2 inch PVC coupling?

The best way to connect two sections of PVC pipe with a 2 inch PVC coupling is to first clean and dry the pipe ends, apply PVC primer and cement to the ends and inside the coupling, then quickly push the pipe ends into the coupling and hold them in place for a few seconds to allow the cement to bond.