answersLogoWhite

0


Best Answer

Uses the interaction between a spinning coil of wire and a magnet

Is found in many appliances with moving parts, like a vacuum cleaner or a blender

apex

User Avatar

Wiki User

βˆ™ 11y ago
This answer is:
User Avatar
User Avatar

Anonymous

Lvl 1
βˆ™ 3y ago
Changes electrical energy to mechanical energyΒ 
More answers
User Avatar

Anonymous

Lvl 1
βˆ™ 3y ago

Changes electrical energy to mechanical energy

Is found in many appliances with moving parts, like a vacuum cleaner or blender

Uses the interaction between a spinning coil of wire and a magnet

APEX

This answer is:
User Avatar
User Avatar

Alex lieseil

Lvl 1
βˆ™ 3y ago
this is correct for Apexx

Add your answer:

Earn +20 pts
Q: WHich of the following would describe an electric motor?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Mechanical Engineering

What would cause a table saw motor to reverse itself while running?

if the power wires for the motor happen to be hooked up backwords


Where on a motor vehicle would cast iron be used?

engine


What happen to the hydraulics system if the cylinder or motor encountered a load it could not move?

excess pressure would be dumped to tank via the relief valve and nothing would go nowhere hopefully. Otherwise you would bend your hydraulic cylinder rod , or sheer the shaft on your motor .


Can 6000 watt electric motor power a car?

Well 1 horsepower is about 750 watts so 6000 watts is 8 horsepower. If you had 8 horsepower running to each of the four wheels ( 24,000 watts ) in direct drive with no efficiency loss do to transmission gearing and removed the engine and transmission then you be able to drive a light weight body like a geo metro. Also the type of engine you are using would be important for a car you should really look at 3 phase ac induction so you would be able to climb hills. Car hub motors are starting to enter the market they have the motor inside the rim and I have been seeing those at 8 hp at 899+. 1 company actually makes 160 hp hub motors for cars. but those cost 10k + each


How do you gear down one quarter hp motor to run a 55 gallon barrel at 12 to15 RPMs what size pullys or sprockets?

Assuming the motor runs at about 3000 RPM, The speed must be reduced by factor of about 200 for 15RPM. Two sets of pulleys or gears would be best. Gears with a chain would not be good due to the high motor speed. You could get 180:1 by putting a 2" pully on the motor, and running a belt to a 30" pulley which is on a shaft along with another 2" pulley, and run that pulley to another 24" pulley. If the barrel is well-mounted and freely turns, you could use it as the second pulley, since it has a 24" approximate diameter. You can also use three sets of pulleys, making it esier to find them. example: 2" motor to 12" on shaft 1 2" on shaft 1 to 12" on shaft 2 2" on shaft 2 to a 10" or 12" one driving the barrel. Consider buying a used worm gear reduction drive to save alot of this trouble. The motor can drive it directly and they come in different ratios.

Related questions

How would one describe a fuel cell car?

A fuel cell car would be defined as a vehicle with an electric motor or engine that uses a fuel cell to produce electricity to power its motor with hydrogen.


Does an electric motor have different resistance than an electric heater?

Yes it would be unlikely an electric motor coincidentally exactly matched the resistance of an electric heater.


How would you make an electric car?

You get lots of batteries and a huge, powerful electric motor


How would you describe an electric guitar's sound?

beautiful


Where on a motor vehicle would brass be used?

Brass bushings inside the electric starter motor.


Would an electric motor start if its capacitor broke down?

No.


What size hydraulic motor is needed to be equal to a 3 hp electric motor?

1 HP electric motor = 1.5 HP hydraulic motor so for a 3 HP electric motor you would need a 4.5 HP hydraulic motor. Also for your information a 1 HP hydraulic motor = 1 2/3 HP gasoline engine.


What type of bearing would be fitted to a fractional kW electric motor?

The type of bearing that would be fitted to a fractional kW electric motor will depend on the model and maker of the motor. Deep grove ball bearings are the most common bearings used.


How much would it Cost to replace electric window motor?

The exact cost to replace an electric window motor varies slightly by the model of car. As of 2014, the average cost for this motor is between 35 and 55 dollars.


What kind of energy is stored in an electric motor?

A machine that turns electricity into mechanical energy is known as an electric motor. The rotor's inertia, as well as the mechanical system that supports the motor, stores energy. It controls the electric motor's torque and speed. It maintains a safe temperature range for the engine, power electronics, electric motor, and other components. It functions as a power source for the electric traction motor. Electrical energy is transformed into mechanical energy by electric motors.


Does an electric motor produce kinetic energy?

I would say maybe because it does move


Where can you buy a replacement electric motor for your lawnmower?

In order to find a replacement for an electric motor I would go to surplusmotors which is a site online where they sell many different types of motors including the one you are looking for.