0
What else can I help you with?
What is the Use of Balance leak off line in Boiler feed pump?
avoid thrust
What is main steam stop valve?
Used in power generation. When steam turbine is on-line the Main Steam Stop Valve is fully open. When offline it is closed. Steam to turbine is controlled thru control valves after Main Steam Stop Valve
Why lantern rings in gate valve are used?
Piping hand book decribes that a spacer ring used in the lantern ring type of packing chamer to permit lubrication of the packing, purging of the shaft or stem, or a leak-off system.
What is bleed valve?
(engineering) A small-flow valve connected to a fluid process vessel or line for the purpose of bleeding off small quantities of contained fluid.
What happens when pulse on time increase in edm process?
Basic what happens. Is with longer on time duration (pulse) you get higher burn rate. But a correct balance of on and off times is how you keep from wearing the electrode more than the part.
What is the Use of Balance leak off line in Boiler feed pump?
avoid thrust
What is balance leak off line?
A balance leak-off line is a component in hydraulic systems, typically found in vehicles or machinery, that allows excess hydraulic fluid to return to the reservoir. This line helps maintain optimal pressure within the system by preventing over-pressurization and ensuring efficient operation. It is often used in conjunction with hydraulic pumps and actuators, allowing for smooth and controlled movement. Proper functioning of the balance leak-off line is essential for the overall reliability and performance of hydraulic systems.
Should the gas line be turned on or off in case of a gas leak emergency?
In case of a gas leak emergency, the gas line should be turned off immediately to prevent further danger.
How do you fix a gas leak?
First off where is it? If it is in line then you can cut that section off and replace it with rubber fuel line of equal size.
Can you cut off rear brake line?
You can cutoff the rear brake line. You will no longer have rear brakes and the fluid will leak out. It is not recommended that can't off the rear brake line, without replacing it.
How do you find a leak in an underground water pipe line system?
Unless you dug the whole line up you probably wouldn't find the leak unless it was a very large leak which would bring the water to the surface, You would be better off just installing a new line. Call a leak detection company. They will find your leak to within inches, and you will be able to dig down, repair the line where it is broken, and repair it.
What is the Use of Balancing line in Boiler feed pump?
Boiler feed pump's suction pressure be aprox. 15Kg/cm2 and discharge pressure be 180Kg/cm2. So the balancing line balance the pressure and protect the boiler feed pump. my quastion is that what is the working principal of balancing leak off
What is the best way to troubleshoot a leak in a sink supply line?
The best way to troubleshoot a leak in a sink supply line is to first turn off the water supply, inspect the line for any visible damage or loose connections, tighten any fittings if necessary, and then turn the water supply back on to check for leaks. If the leak persists, it may be necessary to replace the supply line.
Will the fuel line leak a large amount of fuel after the fuel filter has been changed?
It could leak while the filer is off. Once the filter is back on, there should be no leaks.
What steps should I take to repair a toilet water supply line leak?
To repair a toilet water supply line leak, first turn off the water supply to the toilet. Next, drain the remaining water from the tank and bowl. Inspect the supply line for any cracks or damage. If there is a leak, replace the supply line with a new one. Finally, turn the water supply back on and check for any leaks.
What should I do if I suspect there is a gas line leak in my home?
If you suspect a gas line leak in your home, you should immediately evacuate the premises, avoid using any electrical devices or creating sparks, and call your gas company or emergency services for assistance. Do not try to locate the leak yourself or turn any appliances on or off.
What is the best way to troubleshoot a leak in a toilet supply line?
The best way to troubleshoot a leak in a toilet supply line is to first turn off the water supply, check for any visible cracks or damage in the line, tighten any loose connections, and replace any damaged parts if necessary.
