answersLogoWhite

0

Read the owners manual in the link below. It will explain how to restring the trimmer.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you change the spool on a craftsman weedwacker model 257796022?

To change the spool on a Craftsman Weedwacker model 257796022, first, make sure the trimmer is turned off and unplugged or the battery is removed. Press the tabs on the spool cover to release it, then carefully remove the old spool. Install the new spool by threading the line through the eyelets, then replace the cover, ensuring it clicks securely into place. Finally, wind any excess line if necessary and you're ready to go.


How do you change the spool on a craftsman bushwacker weed eater?

I can't seem to get the spool off.


Cant get the spool out of a craftsman line trimmer?

1. Rotate spool to line up arrows on spool and surrounding casing. 2. Find notch and pry with wide flat-end screwdriver. 3. Spool will pop out.


Looking for Craftsman 24 Volt Weed Wacker part number 71.74805?

Need full spool replacement


How do you remove spool on model 51358?

To remove the spool from model 51358, first ensure the device is turned off and unplugged for safety. Locate the spool cover and gently press or slide it open to access the spool. Carefully lift the spool out of its holder, making sure to note the threading path for reinstallation. Once removed, you can replace or refill the spool as needed.


How do you load weed eater line on a craftsman?

To load weed eater line on a Craftsman trimmer, first, turn off the trimmer and unplug it if it's electric. Remove the spool from the head by pressing the tabs and pulling it out. Cut a length of trimmer line (typically around 10-15 feet), then insert one end into the spool's eyelet and wind the line in the direction indicated by the arrow on the spool. Finally, replace the spool back into the trimmer head and pull the line to ensure it feeds properly.


What spool line do you use on my craftsman 257.798300?

For the Craftsman 257.798300, you should use a .065-inch diameter trimmer line, which is compatible with most standard spool systems. Look for a round or twisted line designed for general use to ensure optimal performance. Always refer to your user manual for specific recommendations or any restrictions on line types.


How do you refills the wire on a craftmans 745400?

To refill the wire on a Craftsman 745400, first, unplug the tool for safety. Open the spool cover by pressing the release button, then remove the empty spool. Place a new spool of compatible wire onto the spindle, ensuring it unwinds in the correct direction, and thread the wire through the eyelet and into the spool. Finally, reattach the spool cover and make sure everything is secured before plugging the tool back in.


How do you thread an twist n edge weed eater model ret115?

To thread a Twist N Edge Weed Eater model RET115, first, unplug the unit for safety. Remove the spool by pressing the tabs on the spool cover and lifting it off. Take a new spool of line, insert the line into the designated hole, and wind it around the spool in the direction indicated by the arrows, ensuring it's tightly wound. Finally, reinsert the spool into the head, making sure the line is threaded through the eyelets, and replace the spool cover securely.


Fuel line diagram for a craftsman 32cc weed wacker?

Mine had a guide hole that broke so I took a small piece of tubing for the fuel line and glued it inside the spool for a guide to start the line, end of line goes inside the guide and wraps around spool


How do you remove spool in weed eater XT110?

To remove the spool in a Weed Eater XT110, first, ensure the trimmer is turned off and unplugged. Press the tabs on the sides of the spool housing to release it, then pull the spool out of the housing. If necessary, you can also unwind any remaining line before replacing or refilling the spool. Always refer to the user manual for specific instructions related to your model.


How do you fill flymo strimmer spool?

To fill a Flymo strimmer spool, first, remove the spool from the strimmer by pressing the tabs or unscrewing it, depending on the model. Next, take the appropriate length of trimmer line (usually specified in the user manual) and insert one end into the spool's designated slot, then wind the line around the spool in the direction indicated by the arrows. Leave some line free at the end, then secure it by slotting it into the spool's holding notches. Finally, reattach the spool to the strimmer and ensure it is locked in place.