answersLogoWhite

0

You don't say if it it the blade or Tranmission drive belt. Get a piece of new carpet remnants and spend about twenty minutes laying on it while you study and inspect the under carriage of the mower. Ideally -jack the mower up to eye level and remove the cutting deck retainers to drop it down one foot to a work bench or platform. Loosen the blade belt keeper post bolts on the deck and main frame to allow removal of the old belt an installation of the new belt. Reposition the keepers and tighten bolts.For the Transmission drive. Remove the cutting deck from the mower. Press the clutch and tie it to the floor.Remove the bolts from the left and right belt keepers at the chassic motor pully. This is as far as I got. It is not simple to get that new belt in there but hopefullt this week I will get er done and report back.

Easiest way I found is to hold up the rear of the tractor with a come-a-long/rope with wheels off the ground,remove both wheels,remove everything holding the rear end in place leaving the 2 back bolts in "loosened to the max" that hold the tranny to the frame,remove clutch pully,remove steering snap ring and pull the steering wheel up out of the way,remove the old belt and replace with a new one,repeat steps backward to finish the job.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you fit drive belt on Murray ride on mower?

We will need some more details... Is it the drive belt or the belt for the blades?it is the drive belt for Murray lawn mower model 38618x92a


What is the long belt from mower to transmission?

The belt from the mower engine to the transmission would be called a drive belt.


how to install main drive belt on Murray riding mower?

To install the main drive belt on a Murray riding mower, first ensure the mower is turned off and the key is removed for safety. Remove the mower deck by disconnecting the belt and any necessary bolts. Next, route the new drive belt around the engine pulley and axle pulley, following the mower's belt routing diagram, which is usually found on the mower's frame. Finally, reattach the deck and check the tension on the belt before starting the mower.


The illustration on the drive belt routing on your john deere gt225?

i need diagram on how to replace deck belt on John Deere GT235 mower


How do you change the drive belt on a Murray lawn mower model 13an772s058?

To change the drive belt on a Murray lawn mower model 13AN772S058, first, ensure the mower is turned off and disconnect the spark plug for safety. Remove the mower deck by taking off the retaining clips or bolts. Once the deck is removed, locate the drive belt routing and carefully slide the old belt off the pulleys. Install the new belt by following the same routing, and reassemble the deck before reconnecting the spark plug.


What is the drive belt size for a Murray 12-36 ride on mower?

its 1/2" x 83" inch od


Why won't my Murray riding mower stop after the drive belt was changed?

I believe it has to do with the main drive belt. (The brake on these types of mowers are almost useless.) If the main drive belt is to short it engages the slip pulley that drives the transmission. I replaced an original belt that was bad with a replacement that was about an inch shorter and my mower would not stop. Replaced the belt again with the exact size required and problem solved ... BUT ...About a month later the same thing happened. The mower would not stop when i released the drive pedal and i ruined my transmission "snapping it out of gear to stop the mower. Now i suspect it may be a worn "slip pulley" causing the main drive belt to ride closer to the spindle on this particular pulley, this , I believe , will cause the pulley to turn faster thus engaging the transmission. This pulley is similar to an adjustable type but it "slips" . On my Troy Bilt it is located in the rear right over the transmission. Hope this helps someone because i have spent hours trying to solve this problem.


What size belt goes on a Murray Riding Lawn Mower - 12.5 HP 40 Cut Lawnmower?

what size belt do i need with a murray riding lawn mower that is a 12.5hp. 40"


Does a Murray riding lawn mower model 42614A 14HP 42cut have an adjustment for the drive belt?

Yes, the Murray riding lawn mower model 42614A typically has an adjustment mechanism for the drive belt. This adjustment can usually be made by loosening the belt tension or adjusting the idler pulley to ensure proper tension and performance. Always refer to the owner's manual for specific instructions and maintenance recommendations for your model.


How do you install drive belt on simplicity prestiege?

To install the drive belt on a Simplicity Prestige lawn mower, first, ensure the mower is turned off and disconnected from the power source. Remove the mower deck by loosening the appropriate bolts and detaching any hangers. Then, thread the new drive belt around the engine pulley and the transmission pulley, following the correct routing as indicated in the owner's manual. Finally, reattach the mower deck and check the belt tension before testing the mower.


How do i Change belt for blades Murray riding mower model 40907X20A?

I changed the blade belt on my Murray mower. Now one blade stops and goes. If I lower the deck the blade stop . What did I do wrong?


Why does the mowing belt jump off on a 42 Murray riding mower?

Belt is stretched or the tension pulley