answersLogoWhite

0

What else can I help you with?

Continue Learning about Movies & Television

What is electronic discharge?

when a capacitor or any chargeable device connected across a load which may be resistive or inductive than the capacitive device discharges and this discharging of this device is called electronic discharge . it is used in CCD (charged coupled devices).


Would voltage in a three phase supply change if neutral wire is disconnected?

No, The voltage will not change. The neutral is basically a ground and is used in conjunction with the phases to create another voltage and act as the return line in an electrical system. "Depending on the system that you have". If you have a 480 volt and used a neutral with it you would have 240 or 277 volt. The 277 volt is what is normally used in office lighting. If you have a 208 or 240 three phase system using a neutral you end up with the 120 volts that is used for just about all normal lighting, receptacles and general use devices used everyday.Additional AnswerWhile the supply voltage wouldn't change, the voltage across each phase of an unbalanced load may change if that load is unbalanced.


Electric power is transferred over large distances at very high voltages Explain how the high voltage reduces power losses in transmission lines?

The conductor used to transmit power has a specific resistance at the given power frequency. Power transmitted is equivalent to I^2 * R, so as the current increases, the power loss from the conductor also increases. To maximize efficiency, power is converted to very high voltages, which decreases the current, which minimizes the power lost in transmission.AnswerThe primary reason for using high voltage transmission lines is because, for a given load, the higher the voltage, the lower the load current. Low voltages would require cables of enormous cross-sectional area making transmission impossible, whereas high voltages allow the use of manageable-sized conductors. A secondary reason is the corresponding reduction in line losses -as described above.


What is used to increase or decrease the voltage across a power line?

The device that increases or decreases the voltage impressed across a power line is known as a voltage regulator. A voltage regulator is a type of transformer where the primary and secondary turns ratio are fairly close; one (primary or secondary) often has a tap changing ability to add or remove several windings, allowing more dynamic control of voltage.


How Convert 200 volt to 230 volt?

If a precision voltage is needed from 200 to 230 an auto transformer could be used. If the load is a 230 volt motor to be operated on 200 then add 15% to the nameplate full load amperage for the calculation for overload protection.

Related Questions

Why the output voltage of transformer increases when capacitive loading is used?

if the load is capacitance then reactive power is injected in the circuit, as we know that reactive power is directly proportional to the voltage, if there is increase in reactive power automatically voltage at load end of the tranformer is increases


What are capacitive loads?

A load, at low frequencies, can be either capacitive, resistive, or inductive. At high frequencies, all three aspects exist. At low frequencies (say <= 10 MHz), a capacitive load is a capacitor, represented by an ideal cap, the MOScap, or a junction cap. An unintentional capacitive load would be the wire or conductor to another wire or conductor or ground. At high frequencies (say >= 1 GHz), all things have a capacitive nature. The higher the frequency, the worst is the capacitive leak A capacitive load means just that the load acts like a capacitor load as opposed to a inductor or resistive load


Why out put current increase in transformer with capacitance load?

ferranti effect...B.*If we use capacitive load the stator MMF aid the rotor MMF. It means that in times of capacitive load rotor flux and main field flux are additive. So the alternator voltage increase with capacitance loading.[By Akhtaruzzaman08]


Why the capacitive voltage transformer and voltage transformer both are used in a substation?

three phases


What is the difference between inductive coupling and capacitive coupling?

A capacitor is a device that resists a change in voltage, proportional to current and inversely proportional to capacitance. dv/dt = i/c An inductor is a device that resists a change in current, proportional to voltage and inversely proportional to inductance. di/dt = v/l In an AC circuit with capacitive loading, the current waveform will lead the voltage waveform; while with inductive loading, the current waveform will lag the voltage waveform.


What would be the effect on the voltage level at the load if the distance between the electrical supply point and the load appliance is increased?

As the resistance in the wire increases due to the longer length the voltage drop across the wire resistance increases. This leaves less voltage across the load. To overcome this voltage drop usually a larger size wire which has less resistance is used. A safe nominal figure for voltage drop is to keep it at 3% of the line voltage.


What is 75va?

75 VA stands for 75 Volt-Amps, which is a unit used to measure apparent power in an electrical circuit. It is the product of the voltage and current in the circuit, regardless of whether the load is resistive, inductive, or capacitive.


Why capacitor is chossen for power factor improvement?

Most of the time a load is inductive. A capacitor counters this effect by making the voltage and current more in phase (so there is greater real power, P=VI*cos(angle)). If the load were to be capacitive in nature, then an inductor would be used in parallel to the load to counter the effects of the capacitors.


Why power factor lags?

When there is an inductive element in the circuit, the current lags behind the voltage. an ideal inductor will make the current lag behind the voltage by 90 degrees..a capacitive element on the other hand will make the current lead the voltage (ideally by 90deg). That's why capacitors in parallel with the system are used a lot for power factor correction


What is thermocouple cable?

The thermocouple is an sesnsing device , when the temperature increases it increases the voltage , that voltage is used for tripping purpose


What is purely capacitive circuit means?

A 'purely capacitive' circuit is a theoretical, or 'ideal', circuit, in which the resistance and inductance of the circuit is ignored, and in which the load current theoretically leads the supply voltage by exactly 90 electrical degrees. It is often used as a means of introducing students to the behaviour of 'real' a.c. circuit which contain contain resistance and inductance, as well as capacitance.


What is a purely capacitive circuit means?

A 'purely capacitive' circuit is a theoretical, or 'ideal', circuit, in which the resistance and inductance of the circuit is ignored, and in which the load current theoretically leads the supply voltage by exactly 90 electrical degrees. It is often used as a means of introducing students to the behaviour of 'real' a.c. circuit which contain contain resistance and inductance, as well as capacitance.