No. There is no illumination, speed or retained accesory power in the factory radio. It is accomplished with car's CANbus communication. To hookup illumination wire on 2006 VW Jetta, tap into white/black wire at the light switch. It dims your lights on your radio. You can also set up different color for day and night.
You need to replace the dimmer switch in your gauge cluster. This was caused by a bad ground happens all the time.
You need to go to a sound shop and buy an adapter that will allow your radio to be plugged into the car's wiring harness. You will also need to ask them which ground wire to cut, so you don't blow out the dimmer switch for your dash lights.
Battery blue/yellow (+) Accessory gray (+) Ground Brown (-) Illumination Green (+) Front speakers Lf pink (+)/ violet (-) Rf light green (+)/ blue (-) Lr Black (+)/ Yellow (-) Rr Red (+)/ White (-)
No, you dont need the code if your gonna put in an aftermarket deck. The only time you would need the code is if you took the stock radio out and unpluged the harness, so its not a problem with a new radio.
look on top of the radio there is a tray. grab the top of the tray and pull out there are clips that hold it together then just let it hang from the wires you will see the radio on brackets then just remove the 4 bolts from the bracket and pull the radio out dont forget to remove the conncetions on the back. once you remove the radio there are 4 screws on each side of the radio that is holding the radio to the bracket. remove those to remove radio from bracket. dont lose those screws your going to need them to install on new radio. any more questions e-mail emezahth@gmail.com
You need to replace the dimmer switch in your gauge cluster. This was caused by a bad ground happens all the time.
If your radio is locked and you DONT know the passcode then you need to call Acura....but if you do know the password...then you should enter it
You would need a mechanic - if you dont know how you may end up in trouble.
You need to go to a sound shop and buy an adapter that will allow your radio to be plugged into the car's wiring harness. You will also need to ask them which ground wire to cut, so you don't blow out the dimmer switch for your dash lights.
i dont have a manuel so i dont know what fuse to be changed,tried the one for radio-int light but that wasnt it. i dont have a manuel so i dont know what fuse to be changed,tried the one for radio-int light but that wasnt it.
A radio tuned to the desired frequency would do the job.
Battery RED + (+) IGNITION SWITCH HARNESS Accessory01 ORN + (+) IGNITION SWITCH HARNESS Ground BLK - (-) RADIO HARNESS Illumination GRY (+) RADIO HARNESS FrontLeftSpeakerPos TAN FrontLeftSpeakerNeg GRY FrontRightSpeakerPos LT.GRN FrontRightSpeakerNeg DARK GREEN RearLeftSpeakerPos BRN RearLeftSpeakerNeg YEL RearRightSpeakerPos DK.BLU RearRightSpeakerNeg LT.BLU
Battery blue/yellow (+) Accessory gray (+) Ground Brown (-) Illumination Green (+) Front speakers Lf pink (+)/ violet (-) Rf light green (+)/ blue (-) Lr Black (+)/ Yellow (-) Rr Red (+)/ White (-)
No, you dont need the code if your gonna put in an aftermarket deck. The only time you would need the code is if you took the stock radio out and unpluged the harness, so its not a problem with a new radio.
To install a dimmer on a 3-way switch, you will need to replace one of the existing switches with the dimmer switch. Make sure to turn off the power to the circuit before starting. Follow the instructions provided with the dimmer switch for proper installation. You may also need to adjust the wiring to accommodate the dimmer switch. If you are unsure, it is recommended to consult a licensed electrician for assistance.
your inner elctrics are not workin you need to take it to a car electrician and get new lights put in Depending on the vehicle, many vehicles have a switch that overrides the interior light feature, That override switch may be turn on. Check your drivers manual. If it is the dash illumination lights that are out, there is a dimmer switch for that feature also. That dimmer switch may be turned down all the way. If all else fails, check the fuses.
To install a dimmer on a ceiling fan, you will need to first turn off the power to the fan at the circuit breaker. Then, remove the existing switch and replace it with a dimmer switch that is compatible with ceiling fans. Follow the manufacturer's instructions for wiring the dimmer switch correctly. Test the dimmer to ensure it is working properly before turning the power back on.