answersLogoWhite

0


Best Answer

Removing plugs - 3.7L engine Each individual spark plug is located under each ignition coil. Each individual ignition coil must be removed to gain access to each spark plug. The coil fits into machined holes in the cylinder head. A mounting stud/nut secures each coil to the top of the intake manifold. The bottom of the coil is equipped with a rubber boot to seal the spark plug to the coil. Inside each rubber boot is a spring. The spring is used for a mechanical contact between the coil and the top of the spark plug. These rubber boots and springs are a permanent part of the coil and are not serviced separately. An o-ring is used to seal the coil at the opening into the cylinder head. 1. Remove necessary air filter tubing at throttle body. 2. Prior to removing ignition coil, spray compressed air around coil base at cylinder head. 3. Depending on which coil is being removed, the throttle body air intake tube or intake box may need to be removed to gain access to coil. 4. Disconnect electrical connector from coil by pushing downward on release lock on top of connector and pull connector from coil. 5. Clean area at base of coil with compressed air before removal. 6. Remove coil mounting nut from mounting stud. 7. Carefully pull up coil from cylinder head opening with a slight twisting action.8. Remove coil from vehicle. 9. Prior to removing spark plug, spray compressed air into cylinder head opening. This will help prevent foreign material from entering combustion chamber.10. Remove spark plug from cylinder head using a quality socket with a rubber or foam insert. Also check condition of ignition coil o-ring and replace as necessary.

Installing plugs - 3.7L engine Special care should be taken when installing spark plugs into the cylinder head spark plug wells. Be sure the plugs do not drop into the plug wells as electrodes can be damaged. Always tighten spark plugs to the specified torque. Over tightening can cause distortion resulting in a change in the spark plug gap or a cracked porcelain insulator. 1. Start the spark plug into the cylinder head by hand to avoid cross threading. 2. Tighten spark plugs to 20 Ft. lbs. torque. 3. Before installing ignition coil(s), check condition of coil o-ring and replace as necessary. To aid in coil installation, apply silicone to coil o-ring. 4. Using compressed air, blow out any dirt or contaminants from around top of spark plug. 5. Position ignition coil into cylinder head opening and push onto spark plug. Do this while guiding coil base over mounting stud. 6. Install coil mounting stud nut.7. Connect electrical connector to coil by snapping into position. 8. If necessary, install throttle body air tube.

3.7L engine coil

User Avatar

Wiki User

14y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

16y ago

Check out this website for everything you could ask for with pictures and lots of explainations: http://www.wjjeeps.com/service/sparkplugs.htm Check out this website for everything you could ask for with pictures and lots of explainations: http://www.wjjeeps.com/service/sparkplugs.htm

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

Look at where the plugs should be, you will see black rectangular things there. These are coil packs. remove the nuts and pull them off. The plugs are now showing. Hope this helps

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change spark plugs 2005 jeep grand Cherokee Laredo 3.7L?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

'How do you change the spark plugs in a 2004 jeep Grand Cherokee Laredo v8 4.7 l'?

it is a diagram of the engine?


Do 2004 jeep grand Cherokee limiteds have platinum plugs from factory?

No.


1993 grand Cherokee Laredo transfer case fluid change?

in the manual it says to use Mopar Automatic Transmission Fluid or equivalent labeled Dexron II or Mercon Quadra-trac 1.2L Select-trac 1.3L Command-trac 1.0L train and fill plugs recommended tightening torque is 30 to 40 foot-pounds i got all of this out of my 1993 Grand Cherokee owner's manual


How do you change brake light switch on 93 Jeep Grand Cherokee?

The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.


Could dirty spark plugs also occur on a 2010 Grand Cherokee like it did on your 1998 Grand Cherokee?

Dirty spark plugs can occur on any make, model, or year. Changing the spark plugs should be done for maintenance, such as when you do a tune up.


In what order do the spark plugs on a jeep cherokee 4.0l Laredo go in?

The firing order is 1-5-3-6-2-4.


What is the firing order for spark plugs going to the distributor cap on a 96 Jeep grand Cherokee Laredo?

V8, 1-8-4-3-6-5-7-2 I6, 1-5-3-6-2-4


Your 99 grand Cherokee has 2 dead cyls no missfire codes it has a 4.7?

bad plugs


Where are the spark plugs located on a 1999 jeep grand Cherokee loredo 4.0?

Beneath their coils.


How do you tune up a 2005 jeep grand Cherokee?

I own a 2006 3.7L grand Cherokee and my tune up consists of spark pug replacements (6) for me, differential fluid change, ATF fluid change (no flush), and PCV. If you have a transfer case you will need to change that as well. good luck!


How often do you change spark plugs in a 2002 grand am gt?

Generally I change platinum plugs at 100K and regular plugs at 50K.


How do you change the spark plugs in a 2001 Jeep grand Cherokee eight cylinder?

The plugs are under the coil packs that are on the passanger side of the vehicle. This is of course if you have the 4.0 engine. I would need to know more about your vehicle to gie you the best answer.