answersLogoWhite

0

I don't know about a Grand Cherokee, but in a 2005 Jeep Wrangler you turn your ignition 3 times with out turning the motor over. Turn your key to start, then off, then start, then off, then start and leave in start position, a code will be displayed in the odometer area. Maybe its the same for a Grand Cherokee.

If that doesn't work a scan tool is required.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Music & Radio

How do you reset the Service 4X4 indicator on a 2006 Jeep Grand Cherokee?

You do not reset it, it is a fault code. It is not a routine maintenance indicator. Fix the problem and the light will go out.


What should to do when showing code spn523512?

When showing code SPN523512, which typically indicates a fault in a vehicle's engine control system, first check the vehicle's diagnostic trouble codes (DTC) using an OBD-II scanner. Review the manufacturer's service manual for specific troubleshooting steps related to that code. Inspect relevant components, such as sensors and wiring, and consider performing tests to confirm the fault. Finally, if necessary, clear the code and monitor for reoccurrence after repairs.


How do you reset EDC for Vito W638?

To reset the EDC (Electronic Diesel Control) for a Mercedes-Benz Vito W638, you typically need to disconnect the battery for about 10-15 minutes to clear any stored error codes. After reconnecting the battery, start the vehicle and allow it to idle for a few minutes to let the ECU recalibrate. If issues persist, using a diagnostic scanner to read and clear any fault codes may be necessary. Always consult the vehicle manual or a professional for specific procedures related to your model.


How do you get DTC codes for on 1998 jeep 5.9 limited?

I'm wondering if you are looking for a list of the Diagnostic Trouble Codes and what they mean or if you are wanting to know how to get any codes that may be stored on board due to a fault that's occurred. On model years 96 and later the only way to obtain the codes is by using a scanner that plugs into an outlet typically located under the dash on the drivers side near the side wall. The scanner will display any active codes. It would probably be less expensive to just take the vehicle in to a repair shop that has a scanner than to buy one. If you want a list of all codes that can be shown you can obtain these codes and an explanation of each by purchasing one of the popular repair manuals from publishers such as Hayes or Chilton. Usually these manuals are available at your local library in their reference section and contain a wealth of other information. Hope this helps and Good luck to you !!


How do diagnose injector fault codes on 1999 V8 jeep?

If you have p0201,p0202,p0203,etc, try replacing the throttle position sensor. The tps can go bad and send out electrical noise which confuses the computer and it sets injector codes.

Related Questions

Diesel diagnostic code 1267 what does it mean?

it depends on the vehicle, some fault codes are manufacturer specific


How do mechanics perform a diagnostic evaluation of a vehicle?

For performance, road test and examine fault codes if any.


How do you get a 2000 Volkswagen beetle out of safe mode?

It needs to be connected to diagnostic equipment for the fault codes to be read and then cleared.


How do you run diagnostic fault codes on a 2005 Jeep Wrangler?

You will need a code retrieval tool available at the auto parts store, plug into the OBDII port by the base of the steering wheel and it will tell you what the fault codes are.


How do you disable the airbag alarm in your 2011 grand Cherokee?

To disable the airbag alarm in a 2011 Grand Cherokee, you typically need to access the vehicle’s diagnostic system using an OBD-II scanner to clear any fault codes related to the airbag system. Alternatively, you can also disconnect the vehicle's battery for a few minutes, which may reset the system. However, it's important to note that disabling airbag alarms can compromise safety, so it’s advisable to consult a professional technician or refer to the vehicle's manual for proper guidance.


99 Grand Cherokee heater actuator problems?

It's actually rare for the actuator motor to fail. The problem is usually a broken blend door and the computer shutting down the system because it detected a fault. You can find diagnostic information at heatertreater.net


How do you extract diagnosis fault codes from a BA Falcon?

To extract diagnostic fault codes from a BA Falcon, you need to connect an OBD-II scanner to the vehicle's diagnostic port, usually located under the dashboard near the driver's seat. Turn the ignition to the "On" position without starting the engine, and then use the scanner to read the codes. Follow the scanner's prompts to retrieve the fault codes, which can then be cross-referenced with a service manual for diagnosis. Alternatively, you can use the "self-test" method by shorting specific pins in the diagnostic connector, but using a scanner is more straightforward.


Where do you view fault codes on your 2001 Chrysler grand voyager?

They are viewed with a scan tool.


How do you clear fault codes on a 2004 International 4300?

To clear fault codes on a 2004 International 4300, you can use a diagnostic scanner compatible with the vehicle's engine control module (ECM). Connect the scanner to the vehicle's diagnostic port, turn on the ignition without starting the engine, and follow the scanner's prompts to access fault codes. Once you've noted or addressed any issues, use the scanner's option to clear or erase the fault codes. Alternatively, disconnecting the battery for a few minutes may also reset the codes, but this method may not clear all stored data.


Why Citroen Xsara beeps at start?

to let you know it's on. or to let you know there's a fault! Get a garage to hook up engine management diagnostic equipment to download the fault codes.


How do you erase Airbag fault code in a Volvo S60?

You will need to go to a dealer or a repair facility that has the Volvo Vida diagnostic computer with the Dice interface. A average diagnostic tool cannot access the SRS codes.


How do you reset citroen c3 engine light?

you will need to plug in an obd diagnostic scanner to read the fault codes then clear them which will turn off the light