answersLogoWhite

0

remove one half inch bolt on the hold down of the dist. but make sure you mark the location of the rotor in relation to the dist. cap or t will be hard to reinstall dist

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Where in a 1992 Jeep Cherokee is the Cam Censor?

Inside the distributor.


Where is horn relay on 1991 Jeep Cherokee Limited?

i have a 1992 Cherokee limited on it its under the lower pannel to the right of the streeing wheel


What is the horsepower of a 1992 Jeep Cherokee Limited 4.0l?

190


How do you replace plugs on 1992 LS400?

you have to remove the distributor covers.


1992 Jeep Cherokee Limited; how remove and replace failed automatic radio antenna?

I was able to remove the existing power antenna on my '92 Cherokee through the wheel well. You have to remove three of the nuts attaching the plastic to the fender as well as pull out two plastic plugs. Pull back the plastic and you will see the power antenna right there. Good luck, Woody


How do you take apart the distributor on 1992 Ford Tempo?

To take apart the distributor on a 1992 Ford Tempo, first ensure the engine is off and the ignition key is removed. Disconnect the battery and then remove the distributor cap by unscrewing the retaining screws. Next, unplug the wiring harness connected to the ignition module and carefully detach the module from the distributor. Finally, remove the distributor by loosening the hold-down clamp and lifting it out, taking care not to disturb the timing position.


How do you install a new distributor in a 1992 dodge shadow 2.2 liter with no turbo?

To install a new distributor in a 1992 Dodge Shadow 2.2 liter, first, disconnect the battery and remove any components obstructing access to the distributor. Note the rotor's position, then remove the old distributor by loosening the hold-down clamp and lifting it out. Install the new distributor, ensuring the rotor aligns with the marked position, and secure it with the clamp. Finally, reconnect the battery and check for proper operation.


Do you have to remove distributor to replace the ignition coil on 1992 Toyota Paseo?

No, you do not need to remove the distributor to replace the ignition coil on a 1992 Toyota Paseo. The ignition coil is typically mounted separately and can be accessed without disturbing the distributor. Just ensure you disconnect the battery and follow proper procedures to safely replace the coil. Always consult the vehicle's service manual for specific instructions.


How do you replace a distributor on 1992 Ford Tempo 3.0 liter?

To replace the distributor on a 1992 Ford Tempo 3.0 liter, first disconnect the negative battery cable and remove any components obstructing access to the distributor. Mark the position of the current distributor to ensure proper alignment, then disconnect the wiring harness and remove the distributor hold-down bolt. Carefully lift out the old distributor, align the new one with the mark, and reinstall it, ensuring it seats properly. Reconnect the wiring harness, secure the hold-down bolt, and reattach the battery cable.


How do you change a icm on a 1992 hoda civic?

Remove distributor cap. remove rotor. remove icm shield. remove all wires from icm. remove two screws holding icm. pull icm strait out


How to wiring for 1992 Cadillac Seville distributor replace pickup and module inside distributor?

remove your distributor cap remove your rotor cap button then look for the modual located on the right side inside of the casing where your distributor sat on remove the modual replace the part make sure you place lube onto the bottom of the modual where it makes contact then place everything back the way it came off hope this helps you.


Where are the fuse and horn relay on a 1991 Jeep Cherokee Limited Edition?

hey i have a 1992 Cherokee the relay is on the right side of the steering wheel behind the lower panel there are three relays there its the middle one i think