0
What else can I help you with?
What do you do if your aftermarket radio wiring harness does not match the factory wires?
Many aftermarket companies sell adapters for aftermarket wire harnesses. They have the original factory harness at one end and you cennect that to the harness that came with the radio. Check your local car audio installer.
When installing a new radio in a 1989 Dodge Caravan winfinity factory radio how do you integrate it with factory amp or bypass the amp?
if you are using an aftermarket wiring harness hook up the remote turn on wire on the new radio it should be blue with a white stripe to the harness also has a blue and white stripe and plug it in this wire turns on the factory amplifier if you are not using a harness you will have to locate the internal amplifier wire of the radio and connect that to the remote turn on on the aftermarket radio = answer = the inernal apm power wire is white on the black wire harness ANSWER if you dont want to use the factory amp. just run new speaker wires to each speaker.
You bought a after market radio and harness for a 91 Eddie Bauer explorer powers up but you get no sound why?
splice the blue amp wire on the harness to the power wire, your car came with a factory amp. that will give you sound.
How can you find out what wires go to what when replacing a Dodge Stratus factory radio with a new one?
One of the easiest and quickest ways to do this, is to go to an audio store and buy a wire harness. It should plug right into the factory plug (providing that it is still intact) and then plug into your new radio. If not, it will have ready to go wires for the harness that came with your radio.
ZX2 Factory Radio Has No Sound But Power?
If your are using a wire kit, you need to connect the blue and/or blue/white wire from the harness to the blue/white wire from your radio. Now if you have cut your wires you will have to locate the one wire that will turn on your factory amp.Good Luck!!!!
How do you remove the radio on a 2000 Eldorado?
Remove the decorative cover from your Cadillac Eldorado radio. Remove the radio retaining screws. The radio will slide out. Remove the wiring harness and the antenna cable from the back of the radio.
How do you remove the ignition switch from a 1989 Cadillac Eldorado?
To remove the ignition switch from a 1989 Cadillac Eldorado, first disconnect the negative battery cable to prevent electrical shorts. Then, remove the steering column cover by unscrewing the screws, and locate the ignition switch. Disconnect the wiring harness from the switch, then remove the retaining screws or bolts securing the switch to the steering column. Finally, carefully pull the ignition switch out of its housing.
How to check cooling fans in eldorado?
Turn your Cadillac on! watch coolant gauge and if the temp is more than 225 your fans should kick on if not shut car off and check harness on fan with a circuit tester and check fuses
Where is the fuse link on a 1996 Cadillac Eldorado for the generator?
On a 1996 Cadillac Eldorado, the fuse link for the generator is typically located in the engine compartment, near the battery. It is part of the wiring harness and may be found near the positive terminal of the battery or along the wiring that leads to the alternator. To access it, you may need to remove some protective covers or components. Always consult the vehicle's service manual for detailed information and safety precautions.
Does the 2004 dodge durango have a plug in under the dash for the factory trailer wiring harness?
The factory wiring harness for the trailers will plug in under the back of the vehicle in the area of the spare tire, the harness plugs into the wiring harness for the tail lights.
How do you remove the driver's side door panel to replace the power window motor on a 1995 Cadillac eldorado?
The 1995 Cadillac Eldorado drivers side door panel is held in place by eight retaining clips. Pry outward on each retaining clip. The door panel will come off. Remove the linkage from the power window motor. Remove the wiring harness from the power window motor. Remove the retaining bolts. Reverse the process to install the new power window motor.
How do you diagnose window problems on a 2002 Cadillac Eldorado?
To diagnose window problems on a 2002 Cadillac Eldorado, start by checking the power window fuse and relay for faults. Next, test the window switch for continuity using a multimeter; if it's faulty, it will need replacement. Inspect the wiring harness for any signs of wear or damage, and ensure the window motor is functioning by applying direct power to it. If these components are working, the issue may lie within the window regulator or the glass track.
How do you change the headlight bulbs on a 86 Cadillac Eldorado?
To change the headlight bulbs on a 1986 Cadillac Eldorado, first, open the hood and locate the headlight assembly. Remove the retaining ring or clips that hold the headlight in place, then pull the headlight out gently. Disconnect the wiring harness from the back of the bulb, replace the old bulb with a new one, reconnect the wiring, and reassemble the headlight assembly by securing it with the retaining ring or clips. Finally, test the new bulb to ensure it works properly.
How to hook up a after market CD player to factory specker wires?
Easy way is to go to best buy get you a wiring harness that plugs into your factory harness.
I put a motor transmission in my 1991 Cadillac DeVille the motor transmission is out of a 1993 Cadillac DeVille I believe that the wiring harness is a little different?
91-93 have the same wiring harness. There is a 2.73 gear ratio (FP3) & 2.97 gear ratio (F79) in that year, so be careful. 94-95 are interchangeable.
How do you install aftermarket stereo in Cadillac Eldorado 1994?
if its a Bose system then you have to hook up the wiring harness in the trunk of the car and run all the wires all the way to the front..its about 9-10 wires...there is an Amp in the trunk of the car on the right side right next to the antenna motor...
What do you do if your aftermarket radio wiring harness does not match the factory wires?
Many aftermarket companies sell adapters for aftermarket wire harnesses. They have the original factory harness at one end and you cennect that to the harness that came with the radio. Check your local car audio installer.
