0
After Leo Fender sold Fender to CBS he stayed on as a design consultant and created the 3-Bolt neck with tilt adjustment as an improvement over the original 4 bolt neck that had no tilt adjustment other than using shims. Fender CBS's production quality, specifically the mismatch of the neck pocket size to the neck heel, resulted in an unstable neck attachment much of the time and gave the 3 bolt neck a bad reputation. Leo later proved the 3 bolt neck worked if done properly with his G&L Guitars.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is a guitar with 3 necks called?
Guitarists simply call it a "tripleneck".
How much money did Leo fender have?
3 euro
Are fender electric guitars bad quality?
Honestly it depends on the guitar but most fender guitars are very good quality. Fender was voted the number 3 highest quality electric guitars in the world. It is behind Gibson and marsall.
What was the name of Eric claptons favorite guitar?
Blackie.A mongrel Fender Stratocaster that he put together from 3 guitars.
What are the 3 most common electric guitar neck attachments?
bolt on - fender for example , you'll see a metal plate on the back of the neck where it joins to the body and 3 or more bolts Set neck - gibson for example , you'll see one piece of wood glued to the body neckthrough - metal and shredder guitars - all of the guitar looks like one piece of wood - the best for guitar builders.
How do you hang front fender on 1976 corvette?
The fender is glued on about 3 in. down on the side at top. bolts on at bottom and on the front bumper. To break the fender lose at the top and off of the inner fender well use a puddy knife and a lot of care. After you remove fender sand the bonding strips and trial fit the new fender in place. Clamp it in place and draw lines so you can install in the same place. Remove fender. Put bonding glue on the bonding strips and on the inner fender. Put the fender back in place using the lines that you drew to line it back up. Clamp in place. Bolt the bumper back to fender and at the bottom. Wipe excess bonding glue off the fender and top surround and wait to dry. Sand and prep for paint. It know where as easy as bolt off and on and paint. Its A lot of time and work. Hope this helps
How do you remove a grill from a 1967 dodge dart?
remove grill,remove bumper,unbolt fender bracket off bumper bracket,take off splash pan in between door and fender,take out fender bolts,don't forget bolts on bottom of fender.there is a bolt under the fender ,back by the door at the top.pull fender off.good luck.
Can i use my fender guitar on xbox 360 guitar hero 3?
No, that's not how that works.
How tall is Douglas Fender?
Douglas Fender is 6' 3".
What is the clearance between the bolt head and anchor plate when you use the taper bolt gauge?
3/8
Do amphibians have necks?
Yes they have necks, to lift their head. yes they have necks called valves it allows it to submerge it into water so no water will enter their lungs
What is the torque specification for 1991 Pontiac lemans 1.6L cylinder head?
Camshaft carrier/cylinder head mounting bolts to 25n.m (18 lb ft.) in figure 21 each bolt an additional 60 degrees each bolt to 120 degrees (additional 60 degrees) each bolt to 150 degrees (additional 30 degrees) bolt sequence as follows; passenger fender 8 4 1 5 9 drivers fender 7 3 2 6 10
Can you break necks in gears of war 3?
Of course, The Sawed-Off Exucution is one that breaks necks from what I saw in the beta.
How do you remove fender in Toyota Camry 95?
1) Open the hood. 2) Remove the 4 bolts along the inner edge (10mm). 3) Take off the wheel well trim and take the bolts off there, and 4) Finally take the bolt in between the fender and the door.
How do you remove the left front fender of a 1994 Ford Ranger?
I have the exact same problem. There are 4 under the hood on top of the fender, 3 above the tire in the wheel well, 2 behind the headlight, 1 you have to open the door and get an extention the bolt is at the top of the fender in the gap of the door, and then there's one down by the mudflap that I can not find, so if you find it, please let me know. :) Hope I helped at all.
What is a guitar with 3 necks called?
Guitarists simply call it a "tripleneck".
What type of bolt do you use in a climbing hanger?
It depends on the design of the hanger and the type of rock. Often it will be a 3/4" or 5/8" expansion bolt
