0
The belt is held in place by a tensioner. it looks like a flat pulley with nothing attached.it has a nut on top that is used to release the pressure on the belt. It is a good idea to get the tool that is needed to do the job. it can be done with regular mechanic's tool. If there is space to use them. make a drawing of the belt pattern before you do anything. it make it much easier to put back on. i made that mistake. Take what ever tool you are going to use and slowy turn the bolt counter clockwise. you should be able to see the tension on the belt release. Slide the belt off of one of the components, and return the tensioner to it original place. notes. the tool needed is not expensive, and can be found at most parts stores. also replace the belt with one that is the same as the one you removed. some have anywhere from 4-7 grooves. hope it helps. duboff
What else can I help you with?
How do you put on a Serpentine belt to an 1986 Cutlass Supreme 305 Cu V8?
You will need to loosen the bolts holding the alternator in place than once theyre loose, theres a long screw that pushes the alternator keeping it tight- loosen that screw and the belt should start becoming loose. Loosen that screw until you can take the belt off then you should be able to replace with a new one. Hope that helps.
How do you tighten the serpentine belt on a 1993 Asuna?
if a serpentine belt is loose, it needs replacing. there is an automatic tension pulley on all serpentine belts. so just buy a new belt and install
How do you put a serpentine belt on a 1995 Jeep Grand Cherokee?
There is no idle pulley on 1995 GC's with 4.0 Inline 6. To replece the serpentine belt; 1) Draw a diagram of the existing routing. 2) Loosen the alternator. 3)Remove old belt and compare to the new belt. 4) Install new belt. 5) Tighten new belt by tightening alternator. on the 5.2 and 5.6 just rotate tension pulley to the right if you are standing in front of Jeep install and release the tension pulley and let it tighten
How do you replace serpentine belt jeep grand Cherokee Laredo 6 cylinder 4 wheel drive?
depends what year it is. i know that the 94 models you just loosens the bolts in back of the power steering pump and the belts should loosen.
How do you route serpentine belt for 1992 Lexus?
There should be a diagram on the underside of the hood.
Replace Serpentine belt on Monte Carlo 3.1?
Loosen the tensioner pulley on your Monte Carlo 3.1 liter engine. Slide the tensioner pulley to the right. The serpentine belt can be removed. Put the new serpentine belt on and slide the tensioner pulley to the left.
What is the system belt in the 95 Monte Carlo called?
serpentine belt.
How do you change idler pulley on 2001 Monte Carlo?
You can change an idler pulley on a 2001 Monte Carlo by first, removing the negative cable from the battery. Using a socket wrench, loosen the tension adjustment bolt. Slide the serpentine belt away from the pulley. Remove?æthe center bolt, and remove the pulley from the engine. Replace the pulley,?æreturn and tighten the bolts, and replace the serpentine belt.
Where is the power steering pump on a 98 Chevy Monte Carlo?
on the front of the engine and it is run by the serpentine belt.
Where is the power steering pump for 2001 Monte Carlo?
on the passenger side of the car and it's driven by the serpentine belt.
Serpentine belt diagram for 1995 Monte Carlo 3.1?
Look under the hood of the car for the diagram or in your owners manual if you have it.
Where can you find a diagram on a 1996 Monte Carlo for the serpentine belt?
Look on your timing chain cover there should be a diagram attached.
How do you loosen the tension on the serpentine belt for a 1997 Monte Carlo z34?
There should be a square hole on the belt tensioner arm that a 3/8's drive ratchet will fit in, just put a pipe over the ratchet for extra leverage and turn the tensioner in the direction that will release the belt.
How do I tighten the serpentine belt on a 1996 Chevy Monte Carlo?
there is no way to tighten your belt it has an automatic belt tensioner if it is making noise it may be the tensioner or the belt also check to see if it routed correctly
How do I release the tension on a 1996 Chevy Monte Carlo for alternator belt?
Near the top of the serpentine belt path is a belt tensioner; it is spring loaded and has a shinney pulley on it. Insert a wrench into this tensioner and pull against it and the tension will be released so you can replace your belt. I am assuming your question is about the serpentine belt.
How do you loosen a serpentine belt for a 1998 Ford Escort ZX2 with an automatic belt tensioned?
Away from the serpentine belt
Where is the water pump located on a 95 Monte Carlo 3.4?
On a 1995 Chevrolet Monte Carlo with a 3.4L engine, the water pump is located on the front of the engine, near the center. It is driven by the serpentine belt and is positioned below the alternator. To access it, you'll typically need to remove the serpentine belt and possibly additional components like the alternator or idler pulley, depending on your specific setup.
