A "fixture unit" is used to design the pipe sizes in a Plumbing system. It does not equate directly to gallons because not all of the fixtures (aka sinks, toilets, tubs etc etc) will be "running" at the same time. Each fixture is assigned a "fixture unit" load by the local authority having jurisdiction (aka the local plumbing code). These are added to together and tables are used to determine the pipe size. EG, a typical bathroom sink is assigned 1.5SWFU (supply water Fixture units) and 1.5DFU (drainage fixture units) BUT a toilet might be 2.2SWFU and 4DFU.
There is no answer as the units are incompatible and therefore not convertible. In plumbing, a Fixture Unit is equal to one cubic foot of water drained in an 1 1/4 pipe over one minute. A Fixture Unit is not a volume or a flow rate unit but a design factor.
The most likely cause is water leakage into the light fixture, causing a ground fault. Make sure the fixture is properly sealed and there are no cracks or damage that could allow water to enter. If the issue persists, consult a professional electrician to inspect the wiring and connections.
The voltage present on the secondary side of the ballast (transformer) varies as to the type of fluorescent tube or bulb that is in the fixture. The voltage will always be higher that the applied line voltage that supplies the ballast.If the fluorescent bulb screws into a lamp type of fixture, then there is no way to measure the voltage at the bulb as the tube and ballast are a combined sealed unit.
The sensing unit on the fixture is thinking that it is night time. If your fixture has a switch before the light, that has to be left on for the sensor to work, try the following. Turn the fixture off with the switch and leave it off for about ten minutes. Turn the switch back on and the fixture will turn on. If the sensor circuitry is working the fixture will turn off after your "delay on" setting is reached. If there is no switch before the fixture check to see if the sensor has been covered, fooling the sensor into thinking it is night time. If it is a hollow tube type sensor, sometimes hornets will lay an egg in there and cover the sensor with a mud patch. As a last resort change the sensitivity control so that is senses daylight sooner, allowing the sensor to shut off earlier. If none of the above work its time to buy a new sensor. These can be bought individually and installed into the old fixture.
You can save space in a small bathroom by installing a combination toilet and sink unit, also known as a toilet sink combo. This unit combines the functions of a toilet and sink into one fixture, allowing you to maximize the space available in your bathroom.
A light fixture/fan unit can run anywhere from 50-200 dollars
In plumbing, a Fixture Unit (FU) is equal to one cubic foot of water per minute. A Fixture Unit is not a flow rate unit but a design factor. This is roughly 7.48 gallons per minute, or 28.3 liters per minute.
There is no answer as the units are incompatible and therefore not convertible. In plumbing, a Fixture Unit is equal to one cubic foot of water drained in an 1 1/4 pipe over one minute. A Fixture Unit is not a volume or a flow rate unit but a design factor.
One fixture unit
A fixture is 7.48 gallons which is equal to 1 cubic foot of waterAlso a fixture unit in storm drainage is roughly 3 square feet depending on pitchTo convert sanitary /waste to storm fixture units for a combined system one has to do interpolation combining all the GPM flow expected from a 10 year frequency
3 gpm
Got no clue
What is the condendsate in GPM flow and what tonnage is the unit
First you must calculate the fixture unints that are needed then based on the FU you can then increase the soil/ waste line to allow the needed pitch for the fixture unit value
A Fixture unit is 7.48 gallons (1 cu ft) or 3 sq ft of drainage Or a pump discharging 1 GPM = 1 FU When in doubt of a proper answer ask a Master plumber of a class A journeyman
By calculations as to friction loss and the fixture unit demands and the heat loss if heating is involved
Depends on the fixture unit value I was looking for and the diameter of the piping involved