answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What is the width of a standard water line PVC pipe?

A standard water line PVC pipe typically has a width (diameter) of either 1/2 inch, 3/4 inch, 1 inch, or 1.5 inches.


When connecting PVC to copper with the help of a rubber sleeve should there be a gap between the 2 pipes or should you place the PVC inside the copper and tighten the gaskets?

The PVC should go inside the copper pipe and the rubber sleeve should be properly tightened to create a watertight seal. There should be no gap between the two pipes. Make sure to follow the manufacturer's instructions for the specific rubber sleeve and fittings you are using.


How many gallons of water will a 3 inch PVC pipe 20 feet long hold?

copper pipe has a wall thickness between .032 of an inch and . 308 of an inchinside diameter .811 of an inch to .434volume=pye*(diameter/2) squared*length=3.14*(0.811/2)squared*(20ft*12 inches)= 123.914636 cubic inches123.914636 (cubic inches) = 0.536426993 US gallons


What size PVC conduit would be required to carry five runs of number 12 AWG conductors?

For five runs of #12 AWG conductors, a minimum of 1 inch PVC conduit would be required to meet the fill ratio requirements, providing adequate space for the conductors while allowing for future additions or modifications.


When replacing 80 ft of old steel pipe which is fed from half inch pipe with copper is there any reason to use 3.4 inch pipe instead?

That's 3/4" pipe, not 3.4" prehaps it would deliver more pressure through the 1/2 inch pipe than 3/4 inch. 3/4" pipe will be less restrictive over the course of the run. Otherwise, no. 1/2" Copper Pipe will do fine, since it has a smoother bore, less restrictive, no lime and rust build-up. The only reason for you to use 3/4" pipe is if you want more volume. The pressure remains the same.

Related Questions

Can a pool pump with 2 inch inlet and outlet be used with 1 12 inch PVC piping?

Yes, it can, this is fairly common. Just use a PVC reducer to connect.


What are the best ways to connect 1 2 od PVC pipe for a plumbing project?

The best ways to connect 1/2 inch PVC pipe for a plumbing project are using PVC solvent cement or PVC primer and cement. These methods create a strong and watertight bond between the pipes.


What is the best way to connect two sections of PVC pipe with a 2 inch PVC coupling?

The best way to connect two sections of PVC pipe with a 2 inch PVC coupling is to first clean and dry the pipe ends, apply PVC primer and cement to the ends and inside the coupling, then quickly push the pipe ends into the coupling and hold them in place for a few seconds to allow the cement to bond.


What are the different types of 2 inch PVC fittings available for plumbing applications?

The different types of 2-inch PVC fittings available for plumbing applications include couplings, elbows, tees, adapters, caps, and reducers. These fittings are used to connect and redirect PVC pipes in various configurations to create a plumbing system.


What is the right connection fitting for a 2 inch PVC shower drain and trap to a 2 inch copper drain pipe?

A fernco or rubber fitting. This made of rubber and had hose clamps on it. You should ask for assistance at a hardware or plumbing shop for a 2" Plastic X 2" Copper Fernco or rubber coupling.


Can you cut into cast iron soil pipe with plastic soil pipe?

You can put up to a 2 inch pipe into a 4 inch. If you are putting 4 inch to 4 inch, either take out a section of the cast and put the PVC in or cut out a section and connect the PVC to the cast with rubber sleeves meant for this. You can use a saddle clamp for the 2 inch. It is a half round piece of PVC with a 2 inch connection in it. It is held on with two U bolts that go around the cast pipe. Put it where you need it and mark the 2 inch hole on the cast. Drill a series of 1/8 inch holes around this circle. when you get them all drilled, you can break out the plug. Try to keep it from falling into the cast pipe. Put the saddle clamp on and connect the PVC pipe as needed. Seal the saddle clamp to the cast pipe with plumbers putty.


What are the standard PVC conduit dimensions used in electrical installations?

The standard PVC conduit dimensions used in electrical installations are typically 1/2 inch, 3/4 inch, 1 inch, 1 1/4 inch, 1 1/2 inch, 2 inch, 2 1/2 inch, 3 inch, 3 1/2 inch, 4 inch, and larger. These sizes refer to the diameter of the conduit.


What is the maximum pressure rating for a 2 inch sch 80 PVC pipe?

The maximum pressure rating for a 2 inch schedule 80 PVC pipe is typically around 400 psi.


What is the maximum pressure rating for a 2 inch schedule 80 PVC pipe?

The maximum pressure rating for a 2 inch schedule 80 PVC pipe is typically around 400 psi.


What is the outside diameter of a 1/2 PVC pipe?

The outside diameter of a 1/2 inch PVC pipe is approximately 0.840 inches.


What is the outer diameter of 1/2 PVC pipe?

The outer diameter of 1/2 inch PVC pipe is approximately 0.84 inches.


Max waterflow in 2 inch PVC pipe?

What schedule pipe?