Look in the area behind the dashboard and see if there is an empty multi-way cable connector there, just waiting for a radio to be plugged into it.
Standard radio connectors usually have several wires on them, not just a "hot" 12 volts and a ground wire. The extra wires are there to connect to loudspeakers in the doors, etc. If you have such a connector then a car accessories shop should be able to sell you a standard plug and cable loom, along with a wiring diagram, so you can hookup the radio and its speakers correctly.
<><><>
Every vehicle has a fuse that feeds "accessories" such as a radio. (Or radio/cassette or radio/CD player.)
What you need to find is that fuse i.e. its position in the fusebox, and the color of the wire(s) connected to it, so you can tap into one of them to power a radio.
Or, better still, if you can find a wiring diagram for the vehicle's electrics, there may already be a wire that goes from that fuse to the radio's fixing position in the dashboard, and from the wiring diagram it should be possible to find out the color of the wire.
Often, if you can get hold of the proper Haynes Maintenance Manual for your vehicle, it will tell you about all the fuses and give a wiring diagram too.
<><><>
Another place to look is in the Owner's Handbook for the make and model of car. They normally list all the fuses but don't usually have any wiring diagrams or wire colors.
Typically, the blue wire is used to power the antenna and is connected to the 12-volt accessory wire on the car stereo. Make sure to consult the specific wiring diagram for your car model to confirm.
To install an amp in an Almera, you will need to connect the amp's power wire to the car's battery, ground the amp to a metal part of the car's chassis, and connect the amp's remote wire to a source that turns on when the car is started. You will also need to run RCA cables from the head unit to the amp for signal input, as well as speaker wires to connect the amp to the car speakers. It's recommended to consult a professional for the installation to ensure safety and proper functionality.
The wiring of the solenoid will depend on what purpose the solenoid serves and the brand. In basic terms, when power is turned onto the solenoid, the inner coil pulls the plunger. The unit needs power and a ground, with a switch or relay to trigger it.
Just simply, connect all the black wires to the black wire coming out of the connector, and all the white wires to the white wire coming out of the connected. Use the blocks with screw in to connect them (pick them up from most car accessories shops like halfords, wilcos....etc).
You may be able to find a free stereo wire diagram for a 1994 Mercury Topaz by searching online on websites such as ModifiedLife or Car Stereo Wiring. You can also try contacting your local library for access to automotive repair manuals that may include wiring diagrams.
A good wire gauge for car radios is 18 gauge. This wire runs between the radio and its power supply from the vehicle.
If you check the radio it should say the red wire is for "switched" power and the yellow wire is for constant power the car is turning off the power to the memory of the radio you need to find a constant power for the yellow wire..
A radio wire diagram for this car can be found in the car's maintenance manual. This manual can be found in an automotive store.?æ
Which wire theres 2....... 12 volt all the time and 12 volt switched?
Yes a remote wire is necessary. You must wire the remote wire from the amp to and ignition source of power (a component which turns on when the ignition in the car is engaged.) i.e. the radio. The remote wire signals for the amp to power on.
their should be a yellow wire in the back of your CD player it is your memory wire it needs positive power if you have an American car this wire should also be yellow coming out of the harness if not then tie it in with the power wire. I am assuming you installed a aftermarket radio if not an yours is original you need a new stereo
Noise filters are generally a kit that comes with instructions. In general: There are three to five wires. They are power in from source, power out to component (radio in your case ) Ground or Grounds depending on the kit, and ocasionally you have to wire the power in or the power up to a second wire.
same way you'd wire a radio in any other car.
Car Radio Battery Constant 12v+ Wire: Orange Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. Run a wire to the fusebox for switched power. Car Radio Ground Wire: Black Car Radio Illumination Wire: Gray Car Stereo Dimmer Wire: N/A Car Stereo Antenna Trigger Wire: N/A Car Stereo Amp Trigger Wire: Pink Car Stereo Amplifier Location: N/A Car Audio Front Speakers Size: N/A Car Audio Front Speakers Location: N/A Left Front Speaker Positive Wire (+): Tan Left Front Speaker Negative Wire (-): Gray Right Front Speaker Positive Wire (+): Light Green Right Front Speaker Negative Wire (-): Dark Green Car Audio Rear Speakers Size: N/A Car Audio Rear Speakers Location: N/A Left Rear Speaker Positive Wire (+): Brown Left Rear Speaker Negative Wire (-): Yellow Right Rear Speaker Positive Wire (+): Dark Blue Right Rear Speaker Negative Wire (-): Light Blue
The correct GAUGE wire is 28 for a car stereo.
You will need a 12volt power source, speaker wire pairs leading to each speaker enclosure, speakers and a radio. You also need a location in which to install the radio.
if you have a after market radio in your car your ground wire is lose or not hooked at all.