0
If you have two 300 watt subwoofers for your vehicle then what size amp do you need?
This is determined by how you wire your subs to your amp. If you get an amp that's bridgeable to mono, then you can wire your subs in series. You will get much more thump if you do it this way. However, make certain that your amp is bridgeable, and stable down to 2 or even 1 Ohms. Check with the dealer you buy from. When wired the way I mentioned, a 300-Watt amp will probably do nicely!
What else can I help you with?
Can a 1200 watt amp give good bass to 2 kicker cvr 12's?
Yes, a 1200 watt amp can provide good bass for 2 Kicker CVR 12-inch subwoofers. Make sure to set the amp gain correctly, match the impedance of the subwoofers with the amp, and use a proper enclosure for optimal performance.
What size wire do you need for a 30 watt mixer?
For a 30 watt mixer, you would typically need a wire size of at least 18 AWG (American Wire Gauge) for power cords and connections. This wire size can safely handle the current draw of a 30 watt device without overheating. It's always recommended to check the manufacturer's specifications for the mixer to ensure you are using the correct wire size.
What size fluorescent bulb replaces a 60 watt incandescent bulb?
A 13-15 watt compact fluorescent bulb (CFL) or a 9-11 watt LED bulb is roughly equivalent to a 60 watt incandescent bulb in terms of light output.
Will 300 watt kicker amp push two tens?
It depends on the specific power-handling capabilities of the subwoofers and their impedance. If the subwoofers have a total power handling capacity that is lower than 300 watts and the amplifier can provide enough power at the required impedance, then it should be able to adequately power the two tens. However, if the subwoofers have a higher power handling capacity or the amplifier cannot provide enough power, it may not be sufficient.
What size breaker for a 1500 watt 120 volt heater?
To calculate the breaker size for a 1500-watt 120-volt heater, use the formula: Breaker size = Power (Watts) / Volts. In this case, 1500 watts / 120 volts = 12.5 amps. Therefore, you would need a 15-amp breaker for a 1500-watt 120-volt heater to allow for a safety margin.
Do you need subwoofers and speakers?
No thanks...I got a nice 4000 watt system.
I have two 1200 watt subwoofers for my car Do you need an amp and if so what size Will they affect your battery much?
First you will absolutely need an amp to power any subwoofers. Nowadays subwoofers come along with amp..& normally one 1200watt subwoofer decrease your car battery lifetime to 2-4 month
If you have two 1400 watt subwoofers that have a 700 watt RMS should you get an amplifier that has the watts of both of the subwoofers together 2800 or should you get an amplifier with only 1400 watts?
get the 2800
Do you need a capacitor for two 1500 watt subwoofers?
it doesn't hurt...but you'll also need a yellow top for deep cycle and a high output alternator to handle the load...
Are all car subwoofers really big?
No the Lanzar MAXP64 Max Pro 6.5-Inch 600-Watt Small-Enclosure subwoofers are very small.
Is an alternator upgrade required to intall subwoofers in older cars?
Depends on the size of the amplifier you are installing and the power required to run it. You can easily install a 500 watt amp with no problems.
What amplifier power will I need to power dual 12" Rockford Fosgate subwoofers?
A Rockford 250 watt amp would compliment a 12" Subwoofer very nicely.
What power of amplifier will you need to for 1000 watt subwoofers?
Find out what the rms is for that sub woofer,if it'1000 then find out what the max is,then you could go between the rms power and the max power to get the right amount of watts.
Is a 900 watt mono amplifier enough power to push 2 10 subwoofers?
yeah it is i had 2 12s and 2 10s hooked up to a 900 watt amp and it hit hard
What size gauge power wire do you need for a 4000 watt amp?
2 or 4
Can a 1200 watt amp give good bass to 2 kicker cvr 12's?
Yes, a 1200 watt amp can provide good bass for 2 Kicker CVR 12-inch subwoofers. Make sure to set the amp gain correctly, match the impedance of the subwoofers with the amp, and use a proper enclosure for optimal performance.
What size wire do you need for a 30 watt mixer?
For a 30 watt mixer, you would typically need a wire size of at least 18 AWG (American Wire Gauge) for power cords and connections. This wire size can safely handle the current draw of a 30 watt device without overheating. It's always recommended to check the manufacturer's specifications for the mixer to ensure you are using the correct wire size.
