answersLogoWhite

0

Loosening rusty bolts is primarily a physical change. This process involves applying force to break the bond between the bolt and the material it is attached to, which does not alter the chemical composition of the rust itself. However, if the rust is removed or reacts with other substances during the process (like using a rust dissolver), that could involve a chemical change. Overall, the act of loosening itself is physical.

User Avatar

AnswerBot

5d ago

What else can I help you with?

Continue Learning about Natural Sciences

Do most bolts loosen clockwise or counter-clockwise?

Most bolts loosen counter-clockwise. Turning a bolt counter-clockwise will typically cause it to unthread and come loose.


How do bolts travel?

Bolts do not travel on their own, but they are typically installed or removed with the use of a wrench or other tool. They can be fastened or unfastened by turning them clockwise (to tighten) or counterclockwise (to loosen).


When do you use a breaker bar?

A breaker bar is used when you need extra leverage to loosen or tighten bolts or nuts that are difficult to turn with a regular wrench. It is especially useful for working on stubborn or rusted fasteners.


How do you change coilpack?

To change a coil pack, first locate it in the engine bay. Disconnect the electrical connector and remove any mounting bolts. Lift the old coil pack out and replace it with the new one. Secure it in place with the mounting bolts and reconnect the electrical connector.


Safety issue of chemical anchor bolt?

One safety issue with chemical anchor bolts is the potential for harmful chemicals to be released during installation, posing health risks to workers. It is important to follow proper handling procedures, such as wearing protective equipment and ensuring proper ventilation. Additionally, incorrect installation or use of incompatible materials can compromise the integrity of the anchoring system, leading to structural failures and safety hazards. Regular inspection and maintenance are essential to ensure the continued safety and reliability of chemical anchor bolts.

Related Questions

How do you change the alternator on a 1993 Buick regal custom?

you loosen the bolts on the opposite sides of it. then, you change the alternater, and tighten the bolts.


How do you loosen the brake caliper to change the brake pads on 99 sunfire there are no bolts to be loosened that can be see?

it has 2 bolts that may be covered by plugs remove plugs


Change a tire on a 1999 Chevy prizm?

to change the wheel and tire on a car just loosen the bolts on the wheel jack it up and replace it


How do you change the transmission pan on a Ford Thunderbird?

loosen lug nuts remove pull bolts drop pan...


How do you change the alternator belt in a 1996 Mazda protege?

What bolts to loosen to put alernator belt on and how to put it on when a/c belt is on.


How do you loosen the AC compressor on the roof of your motor home?

loosen retaining bolts


1999 Monte Carlo caliper bolts loosen in what direction?

Bolts on the caliper of a 1999 Monte Carlo will loosen to the left and tighten to the right.


How do you change a starter on a 1996 suburban?

Disconnect the battery. The starter should have two or three bolts holding it in. And there will be wires connected on it. Loosen the bolts and wiring connectors, then remove the starter from its mount.


How do you loosen the belts on a 1974 Impala?

loosen the alternator bolts to get that belt off and the other belt is loosened by loosening the power steering reservoir bolts.


How do you change front abs sensor on 97 Tahoe?

Find the ABS wheel sensor. Loosen the bolts that attach it to the suspension. Remove the bolts that hold the sensor to the wiring. Remove all other bolts. Remove the ABS sensor.


How to loosen bolts effectively and efficiently?

To loosen bolts effectively and efficiently, use the correct size and type of wrench or socket, apply penetrating oil to help loosen rusted bolts, and use steady pressure in a counter-clockwise direction to avoid stripping the bolt head.


How do you change the serpentine belt on a 1991 Jeep Cherokee?

it is adjusted throught the power steering pump loosen the adjuster bolts remove belt and reverse