answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What is cable size in mm2 required for 450 amps?

To determine the cable size in mm2 required for 450 amps, you need to consider the current-carrying capacity of the cable. The exact size will depend on the type of cable and the installation conditions. For 450 amps, heavy-duty cables with a size of around 240 mm2 or larger would typically be used to ensure safe and efficient operation.


What size cable for 210 amps?

The recommended cable size for 210 amps would be at least 2/0 AWG (00 AWG) for optimal performance and safety. Make sure to consult the National Electrical Code (NEC) or a professional electrician to determine the exact cable size needed based on the installation requirements and conditions.


What size breaker should you use for a unit that draws 58 running amps?

To determine the correct size breaker, you need to ensure that it is rated higher than the running amps of the unit. For a unit drawing 58 running amps, a breaker that is rated for at least 70 amps would be appropriate to provide a safety margin and prevent tripping due to overload.


How do you calculate a sises of cable used for an appliance?

Wire sizes and ampacity are regulated by code. # 14 wire 15 amps, #12 wire 20 amps, #10 wire 30 amps, #8 wire 40 amps, #6 wire 60 amps. These are the most common, a slight variation in amperage depending on the insulation factor.


What size Teck cable is required for a mini split heat pump that is 15 amps?

Two conductor and three conductor #12 Teck cables are rated at 20 amps. This size is one over from the 15 amp rated wire. This is because on motor loads the conductor size has to be 125% of the motors full load amps. Since all that was stated is 15 amps it is better to err on the larger size wire.

Related Questions

What is cable size in mm2 required for 450 amps?

To determine the cable size in mm2 required for 450 amps, you need to consider the current-carrying capacity of the cable. The exact size will depend on the type of cable and the installation conditions. For 450 amps, heavy-duty cables with a size of around 240 mm2 or larger would typically be used to ensure safe and efficient operation.


What is the correct size of cable to used for 50 amps?

8 AWG.


What is square mm in cable size?

cabla sq,mm to amps


What is the cu cable size in 400a load?

A 0.15Cu cable has a rating of 382 amps summer and 476 amps winter. 0.2Cu allows 425/530 amps. That is for outdoor use in overhead lines.


What size cable for 50 amps 3 phase for 650 meters length?

70mm 4core copper cable


What size of cable is needed for 1000 amps?

A parallel run of 750 MCM AWG conductors will handle 1000 amps. if we want 1000amps to flow, 250sqmm cable is enough.


How much capcacity of mm size four core cable well be used in running 1kw three faze motor?

Depends on the type of cable, the method of fixing the cable, the ambient temperature and the way the cable has been run to the motor (i.e in trunking, Conduit) Bascially a cable with a current carry capasity of 2 amps should be fine (1.45 amps with power factor of unity and no de-rating factors). Remember 1mm cable can carry at least 8 amps. Also please improve your English when asking stupid questions!!


What size cable for 210 amps?

The recommended cable size for 210 amps would be at least 2/0 AWG (00 AWG) for optimal performance and safety. Make sure to consult the National Electrical Code (NEC) or a professional electrician to determine the exact cable size needed based on the installation requirements and conditions.


What size cable for hundred and twenty meter run for hundred and twenty amps?

# 2-awg


What size breaker should you use for a unit that draws 58 running amps?

To determine the correct size breaker, you need to ensure that it is rated higher than the running amps of the unit. For a unit drawing 58 running amps, a breaker that is rated for at least 70 amps would be appropriate to provide a safety margin and prevent tripping due to overload.


For 100kw which cable size is good and how to find out cable size?

100 kw is the power drawn by the load. to calculate the cable size you need to know the voltage. From that you can calculate the current. this decides the cable size. for example if the voltage is 400Volts then the current flowing in the circuit when the load is 100 KW will be 250 amps. (100,000/400). for 250 amps to flow with out causing excessive heating of the cable the cross sectional area of the copper cable should be 150 sq mm.for a round cross section the diameter will be roughly 15mm.


Size wire for running 240v 130 amps mig welder?

5 mm