A parallel run of 750 MCM AWG conductors will handle 1000 amps.
if we want 1000amps to flow, 250sqmm cable is enough.
Group Size=40R; Cold Cranking Amps (CCA)=590; 60 Amp/Hr Larger CCA models available. 720 CCA was the highest I have seen online, but 40R is the OEM group size.
bare minimum would be a couple of end wrenches the right size. Sockets and ratchet would be better. Two or three bolts or nuts holding the starter on most vehicles, the positive cable, and the solenoid wire which may just push on, pull off, depending on vehicle
The 2001 Ford Explorer Sport ( the Sport is the 2 door model of the Explorer ) came from the factory with the ( Motorcraft BXT-65-650 battery ) * that's BCI group size 65 , 650 cold cranking amps *
W. Chapman's paintings are worth anywhere from 200$'s to 1000$'s depending on the size. what or where is the best place in NJ or ny to have my painting appraised
You might check the Amps size of the fuse. A lot of times, if you are using a fuse with too little Ampage, it can cause the fuse to blow. Your owner's manual should tell the proper size of fuse for that specific circuit.
The only way to determine the cable wire size needed for a 1000 watt air conditioner is to find the load size. To get the load size you will need to use the formula Amps = Watts or Volts. With that being said, you will need a number 14 copper wire.
The recommended cable size for 210 amps would be at least 2/0 AWG (00 AWG) for optimal performance and safety. Make sure to consult the National Electrical Code (NEC) or a professional electrician to determine the exact cable size needed based on the installation requirements and conditions.
To determine the cable size in mm2 required for 450 amps, you need to consider the current-carrying capacity of the cable. The exact size will depend on the type of cable and the installation conditions. For 450 amps, heavy-duty cables with a size of around 240 mm2 or larger would typically be used to ensure safe and efficient operation.
The size of a cable needed for 3.5KW shower can range from 4.0mm.
cabla sq,mm to amps
8 AWG.
Wire sizes and ampacity are regulated by code. # 14 wire 15 amps, #12 wire 20 amps, #10 wire 30 amps, #8 wire 40 amps, #6 wire 60 amps. These are the most common, a slight variation in amperage depending on the insulation factor.
A 0.15Cu cable has a rating of 382 amps summer and 476 amps winter. 0.2Cu allows 425/530 amps. That is for outdoor use in overhead lines.
70mm 4core copper cable
It is not possible to answer the question without knowing the supply voltage. Conductors (wires) are sized according to current (amps), not KW. Amps = watts / volts As you can see, there is no way to determine amps (needed to size the wire), without knowing both the KW and the voltage. If this is on a test, it is a trick question. If you are really trying to size a cable for a real stove, hire a licensed electrician! Improperly sized wire can start a fire.
The formula for amps when kilowatts are stated is; kW x 1000/1.73 x Volts x pf. 10 x 1000/1.73 x 415 x .8 = 10000/574 = 17 amps. The electrical code states that motor feeders have to be rated at 125% of the motors FLA (full load amps). 17 x 125% = 21 amps. A #10 copper conductor with an insulation factor of 75 or 90 degrees C are both rated at 30 amps.
Cable sizing is based on load amperage. The formula you need to use is Amps = Watts/Volts. Amps = 1000/220 = 4.55 amps. A #14 copper wire with a insulation factor of 60, 75 and 90 degrees C is rated at 15, 15 and 15 amps respectively.