answersLogoWhite

0

12v bulbs are typically more cost-effective to run compared to 240v bulbs because they consume less electricity. This is because 12v bulbs have lower wattage ratings and are more energy-efficient. Additionally, 12v systems may also have lower installation costs and require smaller wiring sizes, resulting in overall savings.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you run 12v winch off 240v power?

You can use a step-down transformer to convert the 240V power supply to 12V required for the winch. Make sure the transformer is capable of handling the power requirements of the winch and is properly wired to ensure safety. It's recommended to consult with a qualified electrician to set up the connection safely and effectively.


Can 120v 20w bulb be used in low voltage 12 volt system?

No, a 120V 20W bulb cannot be used in a 12V system. The bulb is designed to operate at 120V, and using it in a 12V system would likely cause it to burn out or malfunction. It is important to use bulbs that are designed for the specific voltage of the system.


Can GFCI circuit breaker handle a 240V circuit with a 120V circuit sub-paneled off if it?

I don't know if you are trying to ask if you can run a 240V panel off a GFCI or run a 120 V sub panel off of a GFCI. Can you clarify please,,,Thanks


Can a 240v stove run on 2 legs of a 208v system?

No, a 240V stove requires full 240V to operate correctly. Running it on 208V may cause the stove to malfunction or not work at all. It is important to match the voltage requirements of the stove with the power supply for safe and proper operation.


Can you tie into your kitchen run to get your 240V to a receptacle?

No, tying into a kitchen run to power a 240V receptacle is not recommended. It's best to install a dedicated circuit for the receptacle and ensure that the wiring and circuit breaker are appropriately sized to handle the load. This will help prevent overloading the circuit and ensure safety.

Related Questions

Can you run a 12 volt vw beetle with a 6 volt generator?

No. The ignition needs 12v to run, the starter needs 12v to crank, the bulbs all need 12v to get bright enough...


How many 12V 50W bulbs can you run on a 20-60VA transformer?

A 60VA transformer can run only one 50W bulb.


How do you run 12v winch off 240v power?

You can use a step-down transformer to convert the 240V power supply to 12V required for the winch. Make sure the transformer is capable of handling the power requirements of the winch and is properly wired to ensure safety. It's recommended to consult with a qualified electrician to set up the connection safely and effectively.


What would cause light sockets to read 130V in a 240V system when the light switch is off?

More than likely, your 240V system has branches that supply a standard household 120V to things like lighting outlets. Most light bulbs in the US run on 120V so this is probably a convenience feature. Otherwise you would have to go to a specialty store and buy 240V bulbs.


Can you splice a car stereo into a wall outlet?

No. Car stereos run on 12v DC power. A wall outlet, depending on where in the world you are, gives out either 110-120 or 220-240v AC power.


Can 240V washer run on 120V outlet?

No.


Will a 12v lithium battery rated at 1000ma run a 12v 100w light bulb?

no


Can 120v 20w bulb be used in low voltage 12 volt system?

No, a 120V 20W bulb cannot be used in a 12V system. The bulb is designed to operate at 120V, and using it in a 12V system would likely cause it to burn out or malfunction. It is important to use bulbs that are designed for the specific voltage of the system.


Can a 12v 550ma device be run by a 12v 210ma supply?

No, the supplies output is too small. To run a 550mA device a supply source of 600mA and larger would be needed.


Will a 240v 3 phase welder run better than 240v 1 phase?

Yes, because you will be able to maintain current flow between phases.


Will a diode work as a light dimmer when switched or added in series to an incandescent 120 volt AC bulb?

Actually, I have seen this in a respected electronics magazine (Elektor) quite some time ago: A diode (selected to be capable to handle the amps, the voltage and the heat from the bulb - if placed inside the lighting fixture) is used to "cut off" one half of the AC sine wave and thus sending pulses of 120V to an incandescent light bulb, simulating a simple dimming device. The proposal was meant to run 240V bulbs at 50% of their brightness but I am pretty certain this concept can be used to run 120V bulbs from 240V power. One other way of connecting 120V bulbs to 240V would be to connect two 120V bulbs OF THE SAME WATTAGE in SERIES, so the two bulbs form their own voltage divider. Not sure what happens if one bulb burns out - I would expect the other one to blow too, as a dying light bulb represents zero Ohms (plasma/arcing) for a few milliseconds before it goes dark forever.


What is the cheapest car to run?

2