answersLogoWhite

0

It is the control

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Natural Sciences

What is the role of water in the Benedict reagent?

It acts as a control for the experiment so that you can compare the result (of benedict's test in water) with the other test (using food with sugar)


Mario places 10 mL of water in a test tube and heats the liquid over a Bunsen burner for 2 minutes. After removing the test tube from the Bunsen burner there are 6 mL of water left in the test tube. T?

After heating the water for 2 minutes, the reduction from 10 mL to 6 mL indicates that 4 mL of water has evaporated. This evaporation occurs due to the increase in temperature, which allows water molecules to gain enough energy to transition from the liquid phase to the gas phase. The remaining 6 mL represents the water that did not evaporate during the heating process.


How do you calculate phase voltage of a three phase four wire system?

Phase voltage is determined by the wiring of transformer that serves the building. To test phase voltage use a volt meter and put one probe to ground and the other to each phase and observe the reading, this will give you a phase to ground voltage reading. Next test phase to phase (1 to 2, 1 to 3, and 2 to 3) to see if it's 208, 240, 277, or 480. Only licensed electricians should perform these tests. DAW


Conditions needed to satisfy in order to porgress from the test execution phase?

In order to progress from the test execution phase, the following conditions need to be satisfied: all test cases planned for execution must be executed, defects must be logged and tracked, test progress must be monitored and reported, and exit criteria must be met to decide whether to move to the next phase of testing.


What do you think will happen to the potato pieces if increase the amount of salt in each test container?

Increasing the amount of salt in each test container will result in a higher concentration of salt in the surrounding solution. This will cause water to move out of the potato pieces via osmosis, leading to a decrease in their size and weight as they lose water and shrink.

Related Questions

What was the role of the water test tubes in each phase?

It is the control


Can I test wires from a 3 phase motor to see if its configured in low or high voltage?

Using a multimeter, check the continuity of motor winding from phase to phase ( U to V, V to W , W to U ). Each phase to phase must have a continuity if winding is OK. If any particular phase fails the continuity test, your motor is probably burnt.


How to Test for single phasing?

You can do that in one of three ways: 1- current on each phase, 2- phase to gnd voltage, 3- phase to phase voltage, preferably with multiple meters, the three lines has to be balanced within ~ 3%


How do you zero phase current tranformer test?

How do you zero phase current transformer test


What is polarity test and continuity test?

a test to be conduct for find the phase...


What is the role of water in the Benedict reagent?

It acts as a control for the experiment so that you can compare the result (of benedict's test in water) with the other test (using food with sugar)


Load test on 3 phase induction motor?

When you do a load test on a 3-phase induction motor you are checking the power factor, viz slip, and efficiency of the motor. You can test various loads with this test.


Why Y phase is high in YNyn0 when doing magnetic balance test?

because y phase is y phase ...it is not b phase or R phase so it is high


Can you test single phase device on three phase supply?

yes in star trek


Load test on single phase transformer?

The dc tests that can be done on a transformer are to measure the resistance of each windings and to measure the insulation resistance between the windings and between each winding and the transformer case.


Procedure for sumpners test?

Procedure for sumpners test is the single phase transformer. This is a back to back test.


How do you calculate phase voltage of a three phase four wire system?

Phase voltage is determined by the wiring of transformer that serves the building. To test phase voltage use a volt meter and put one probe to ground and the other to each phase and observe the reading, this will give you a phase to ground voltage reading. Next test phase to phase (1 to 2, 1 to 3, and 2 to 3) to see if it's 208, 240, 277, or 480. Only licensed electricians should perform these tests. DAW