0
What else can I help you with?
What happens to energy put into a pulley that is not used?
Energy that is put into a pulley but not used is typically converted into other forms of energy, such as heat or sound. Friction and other inefficiencies can cause some of the input energy to be lost in the system.
What is the answer to when you want to pull downward to lift something the main advantage of passing a rope upward and through a single pulley rather then just put over the branch of a tree is that?
Passing a rope upward and through a single pulley increases the mechanical advantage, making it easier to lift heavy objects by applying less force. This setup also allows for better control and direction of the lifted object compared to just putting the rope over a tree branch.
Why does someone feel cold in a string vest but warm if they put a tight shirt over it?
In a string vest the body heats trapped in air cushion in between whereas if we wear a tight shirt. it cannot hold inside air and body feels colder.
What is the hole in your clothing you put your arm through called?
That hole is called a sleeve. It allows you to put your arm through and comfortably wear the garment.
What if you put a ticking clock in a box and pump all the air out the clock is on a thin string so that it is not touching the walls of the box would you hear the clock ticking?
No, you would not hear the clock ticking because sound requires a medium, such as air, to travel through. Without air in the box, there would be no medium for the sound waves generated by the clock's ticking to travel through, so the sound would not reach your ears.
How can a fixed pulley and movable pulley be put together?
With the string from the movable pulley
How can a kid mske a trap with only a motion detector a string and a Nerf gun?
make a trip wire. then get a pulley. then get the string to go through the pully then put the string on the trigger then tie the ends of the string together.
How do you double knot a string of pearls?
Put them in your pocket & go for a run.
How do you restring the pull cord of a Briggs and stratton tiller?
Remove the cover of the engine which has the pullstarter in it, Clean it well before starting, Looking at the underside - there are three bent over metal tabs, and a pulley, Remove the leftover string noting where the knot sat and where the hole is, WITHOUT removing the pulley, unbend the tabs that are holding the pulley in, Keep a hand on the pulley AT ALL TIMES, as if it comes out so will the spring, Tie a knot in the end of the new string, and feed the other end into the hole in the pulley, and out the hole in the housing, Put the starter handle on the end of the string and tie a big knot, You shoud now have the string fitted, ready for tensioning, To tension, pick the string out between the pulley and the housing, near where the little notch is in the pulley, so you can grab the string and pull some out like a loop, Then grabing the string, which is in the notch and now has some slack, turn the pulley and string together, in the direction (usually anticlockwise) it turns when your pulling the starter handle, go around a few times, then while still holing the pulley in - pull the string by the starter handle to suck in the slack, Repeat this until required spring tension reached, Bend over at least on tab to keep the pulley in the housing.
How can you put a string through a potato?
is there a needle attached to the string if not there r other ways make a hole and put the string inside and go in and out and start moaning and giggiling
How do you use string in C programming?
You put it between double quotes, "like this".
Where do you put your Nintendo DS pen on your Nintendo DS?
On the lid of your Nintendo ds pen, there is a bit of string. On your ds (where you put you game card in), there will be 2 small squares. Put the string through one of them and it should come out of the other. Then open the string and put the lid through the gap then pull on the lid.
How do you make a scooby doo wristband?
You get some Scooby beads and put them in through the string then tie the string
What do you put on a screaming pulley bearing?
Put on a new pulley bearing.
How to put a guitar string on properly?
To put a guitar string on properly, first unwind the old string and remove it. Insert the ball end of the new string into the bridge of the guitar. Thread the other end of the string through the tuning peg and tighten it. Tune the string to the correct pitch and trim any excess string.
What is a string instrument classified as?
String instrument is a classification in itself. String instruments include violin, viola, cello, double bass, guitar, harp, etc. Some people put piano under the string classification as well.
How do you tighten a yoyo string on your finger?
put your finger through the loop and then pull.
