0
How are a Genecon and a Battery similar when they are connected to a circuit?
Wiki User
∙ 10y ago
i need help
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is an complete circuit?
A circuit is complete whenever current can flow from the battery (or what is producing current), through the circuit, and back to the battery. A complete circuit could contain just a battery and one wire. An incomplete circuit could be a battery with a wire attached to just one terminal, because current cannot flow all the way through the circuit in this case (i.e. cannot flow through the battery). note: not all elements in a circuit may have current flow in a complete circuit. For instance, a light bulb may be shorted but you still have a complete circuit.
Is polarity important when testing when testing continuity?
testing polarity of CT by Flick test . A centre zero voltmeter is connected across CT secondary .A 1.5V battery is touched to primary of CT .the deflecting of pointer should be similar in case of each CT to be connected in same protection .
Where does the energy needed to start a car come from?
Car's normally get their energy from gasoline, or a similar fuel - which stores the energy as chemical energy.
How do you make a battery powered toy that can move has a light and makes a sound?
The parts required for this project can be acquired from your local electronics store. You can buy lights, buzzers and motors, and can usually buy gears as well. If you want more than just a single tone played continuously, you will have to make or buy a circuit to do this. To actually make this toy, you will have to link a motor to the axles. You could run the light and sound off the same circuit, either in series or in parallel, or off a separate circuit. You may want to add a switch to turn it off. Your best bet is to go to an electronics store, and ask if they have a kit which is similar. You could use this as a base model, and add other features on top.
How can you limit amperage drawn through a circuit without decreasing voltage I need to variably restrict amperage drawn from point 12amp to 1amp with the turn of a dial at 240v AC Does a device exist?
i have a similar problem but mine doesn't need to be controlled with a dial. i think a carbon pile may be your answer. an old carbon pile battery tester through the circuit. either that or several resistors, select amount of resistors your circuit passes through with your dial switch, like a blower motor in your car would use. my problem however is finding a way to limit amps to 75 between two sets of batterys where amps have the potential of fluctuating from 0 to2600. a cannot just put a resistor in the circuit because they resist a set amount of ohms rather than only let a set amount of amps pass through. like a breaker or fuse. but i don't want a breaker or fuse because the circuit will be broken with them. I'm working on a 12v dc circuit. I'm not sure how a carbon pile will react on ac but it something to think about.
What is an complete circuit?
A circuit is complete whenever current can flow from the battery (or what is producing current), through the circuit, and back to the battery. A complete circuit could contain just a battery and one wire. An incomplete circuit could be a battery with a wire attached to just one terminal, because current cannot flow all the way through the circuit in this case (i.e. cannot flow through the battery). note: not all elements in a circuit may have current flow in a complete circuit. For instance, a light bulb may be shorted but you still have a complete circuit.
What happens when the car battery connectors connect together?
When a car battery in connected to itself (i.e. You connect jumper cables onto a battery and then connect the other two connectors to each other), you create a continual circuit with the battery and nothing else. A similar effect is when you hold a 9 Volt battery to your tongue and you feel a small but continual "zap". Imagine this effect, but much greater. Sparks will appear when the connectors are first connected. Warning: Do not do this. This will damage your car battery. The only reason you should connect a car battery through jumper cables is to connect it to another car's battery in order to "jump" a car.
Are no load and short circuit similar?
No. No load and short circuit is not similar. No load can be 1) Either open circuit i.e. Only Potential is available and load is not connected 2) Load (i.e. motor etc ) is connected but not working with full load or full capacity. In this case the current will flow through the circuit depending on the load. It means No load condition is a condition where no current or a small ( relative / comparative term) current is flowing through the circuit. In Short circuit the load side resistance/ impedance become so less that very high amount of current is passing through circuit.( The protection is therefor required for any circuit) No load and and short circuit is not similar. Thanks
How connecting an electric device to a battery produces a current in the device.?
If we connect a battery to a device and complete a circuit, current will flow in that circuit and through the device. A battery (in good condition) is an electrical storage device. Most of the ones we are familiar with are chemical cells. There are chemicals inside that would like to react, but cannot unless there is an external circuit through which electrons can move to get from one electrode in the battery to the other. The potential chemical energy in a battery can be converted into electrical energy by completing that circuit. There is a force called voltagethat arises between the electrodes of the battery. And this voltage (electromotive force, or EMF) is the way that the chemical potential energy expresses itself. Because the battery can convert chemical potential energy into electricity owing to that EMF between the electrodes, connecting a circuit across the battery will allow current to flow as the chemical reactions in the battery proceed. A very rough analogy can be drawn by looking at gravitational potential energy. If a Bowling ball is sitting on the floor and it is lifted onto a table, its gravitational potential energy has been increased. This is distantly similar to the chemical reactions that want to occur in the battery; they are potential energy, too. If the bowling ball rolls off the edge of the table, the potential energy is converted into kinetic energy by gravity. When we hook up an external circuit to the battery, the chemical potential energy (expressed as voltage) drives electrical current through that circuit and the device in it. The circuit here is composed of conductors and the device. Electrons in the conductors are hanging around in the conduction band, and if a voltage is applied, those electrons will begin moving in response. The device must be conductive to some extent, and it, too, will have this electron current flowing through it. The battery has been connected to a circuit and drives current through that circuit. The chemical potential energy in the battery is converted into electrical energy in the circuit and the device connected to it.
How does connecting an electric device to a battery produce an current in the device?
If we connect a battery to a device and complete a circuit, current will flow in that circuit and through the device. A battery (in good condition) is an electrical storage device. Most of the ones we are familiar with are chemical cells. There are chemicals inside that would like to react, but cannot unless there is an external circuit through which electrons can move to get from one electrode in the battery to the other. The potential chemical energy in a battery can be converted into electrical energy by completing that circuit. There is a force called voltagethat arises between the electrodes of the battery. And this voltage (electromotive force, or EMF) is the way that the chemical potential energy expresses itself. Because the battery can convert chemical potential energy into electricity owing to that EMF between the electrodes, connecting a circuit across the battery will allow current to flow as the chemical reactions in the battery proceed. A very rough analogy can be drawn by looking at gravitational potential energy. If a bowling ball is sitting on the floor and it is lifted onto a table, its gravitational potential energy has been increased. This is distantly similar to the chemical reactions that want to occur in the battery; they are potential energy, too. If the bowling ball rolls off the edge of the table, the potential energy is converted into kinetic energy by gravity. When we hook up an external circuit to the battery, the chemical potential energy (expressed as voltage) drives electrical current through that circuit and the device in it. The circuit here is composed of conductors and the device. Electrons in the conductors are hanging around in the conduction band, and if a voltage is applied, those electrons will begin moving in response. The device must be conductive to some extent, and it, too, will have this electron current flowing through it. The battery has been connected to a circuit and drives current through that circuit. The chemical potential energy in the battery is converted into electrical energy in the circuit and the device connected to it.
How are open circuit and closed circuit similar?
Not similar at all. They are opposites.
Is there aluminum in batteries?
There are alumium batteries . The aluminium-ion battery is conceptually similar to the lithium-ion battery: when the battery is discharged atoms from a metal anode are oxidised, releasing electrons into the external circuit. When recharged, the electrons are driven back to the anode.
What body system is similar to an electrical circuit?
blood circulatory system is similar to an electric circuit
How was your battery similar to Volta's battery?
My battery was similar to Volta's battery because both hadpaper in between and one rod on each side.
What is the effect on total resistance of adding this third bulb?
If a fourth bulb were added in a similar way to the three existing bulbs, the resistance in the circuit would go up if the bulbs were series connected, and it would go down if the bulbs were parallel connected.
What causes the battery and brake light to come on when the alternator connector is plug in and it will go out when it is disconnected and sometimes with it connected it will kill the battery?
Its a good possibility Your diodes are burnt out, its time to replace your alternator, i had a similar problem on a 95 lumina with a 3.1l motor
How is an automobile battery similar to a energizer battery?
They are both batteries
