answersLogoWhite

0

Braking while turning can cause loss of traction and control, increasing the risk of skidding or sliding. It is generally recommended to brake before entering a turn and then accelerate gently through the turn to maintain control of the vehicle.

User Avatar

AnswerBot

3mo ago

What else can I help you with?

Continue Learning about Physics

Do you brake when turning?

Yes, it is important to brake when turning to help control your speed and maintain control of the vehicle. Braking while turning can help prevent skidding or losing control of the car.


Should you brake while turning?

Yes, it is generally recommended to brake before entering a turn rather than during the turn to maintain control and stability of the vehicle. Braking while turning can cause the vehicle to lose traction and potentially lead to a loss of control.


What is the ability to change the speed or direction of the vehicle?

The ability to change the speed or direction of a vehicle is controlled by the accelerator and brake pedals, as well as the steering wheel. Increasing pressure on the accelerator pedal speeds up the vehicle, while pressing the brake pedal slows it down. Turning the steering wheel changes the direction of the vehicle.


How does the Brake Piston Cube work?

The Brake Piston Cube is a cube-shaped tool used to retract brake caliper pistons in vehicles when changing brake pads. Its design allows it to fit into the caliper housing and apply even pressure to retract the pistons back into the caliper, facilitating easier brake pad replacement. By turning the Brake Piston Cube, the pistons are compressed uniformly without damaging the caliper or seals.


How is evaporation different from boiling?

Evaporation is the process of a liquid turning into a gas at a lower temperature, while boiling is the process of a liquid turning into a gas at its boiling point.

Related Questions

Do you brake when turning?

Yes, it is important to brake when turning to help control your speed and maintain control of the vehicle. Braking while turning can help prevent skidding or losing control of the car.


Could the rotors be that bad after installing new front brake pads on a 2002 Chevy Blazer when you are driving and apply the brakes it pulsates?

Either warped rotors or drums can cause pulsating. Apply the parking brake slowly while going about 15mph and see if t pulsates. If it does, it is the drums that need turning. If not, it is the rotors that need turning.


How do you release hand brake cable?

Pull gently while turning 90 degrees clockwise.


Should you brake while turning?

Yes, it is generally recommended to brake before entering a turn rather than during the turn to maintain control and stability of the vehicle. Braking while turning can cause the vehicle to lose traction and potentially lead to a loss of control.


Why would the front end of a 1996 Dodge ram 1500 4WD make a squeaking noise while turning left or right?

Most likely the front squeaking while turning is a brake issue. If this is the case and it is left uncorrected, you could be looking at a very expensive brake job.


What could be the problem on a 2002 mercury mountaineer 2wd that has a noise when driving and especially turning left?

Bad wheel bearing? Brake pads worn?


When turning right and pressing the brake you have a squeek What could this be?

Probably brake pads.


On a 2000 Dodge 2500 4x4 diesel after turning front brake rotors and replacing brake pads why do ABS and brake trouble lights remain on?

you might have a bad speed sensor or a bad front wheel bearing causing the light to go onTRy replacing the sending unit they go bad very often turning rotors and replacing pads is not the way to fix this. it is the abs sending unit and it needs to be replaced.the correct part you will need to replace is called the wheel speed sensor not sending unit


Brake lights don't work on 1994 Chevrolet diesel but the turning and clearance lights work?

You have a bad ground to the from the glow plug relay to the engine block


1986 Chevy tries to go while holding the brake in drive?

possible have a bad master cylinder


Why does Parking brake light go on when turning and applying brake?

Faulty or over sensitive parking brake switch or sensor.,


Where is the brake light switch?

THE BRAKE LIGHT IS LOCATED BELOW THE DASH. LOCATE THE ARM HOLDING THE BRAKE PEDAL AND YOU WILL SEE A SWITCH THAT COMES OUT WHEN THE PEDAL IS DEPRESSED TURNING THE LIGHT ON. WHEN THE BRAKE IS RELEASED THE SWITCH DEPRESSES AGAIN TURNING THE LIGHT OFF.