answersLogoWhite

0

That's one of the pickiest things to do. On some washers you can raise the whole top surface to do it, on others you have to take the whole casing off. Look carefully along the front seam, where lid sits on casing, you may see two clips. If you do slip a flat screwdriver just into the slit and try to wedge it open. If it doesn't work then you have the other kind, sorry.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

Washing Machine Lid Switch Repair?

If your washing machine will agitate, but refuses to spin out, you more than likely have a bad lid switch. A lid switch, when working properly, tells the washing machine when the lid is closed, thus allowing the washer to spin out. A faulty switch will signal that the lid is still open, even though it isn't, and the water will not spin out. Repairing a lid switch is easy for the average do-it-yourself person with some instructions from internet sources, especially videos. These switches will run anywhere from $20-$60 depending on the machine and are found at your local appliance repair centers.


Why is my Hotpoint washing machine not draining properly?

Your Hotpoint washing machine may not be draining properly due to a clog in the drain hose or pump, a faulty pump, or a malfunctioning lid switch. It is recommended to check these components and clean or replace them as needed to resolve the issue.


Why is my washing machine stuck on rinse and how can I fix it?

Your washing machine may be stuck on rinse due to a malfunction in the timer, water inlet valve, or lid switch. To fix it, you can try resetting the machine, checking and cleaning the water inlet valve, or replacing the timer or lid switch if necessary. If these steps do not work, it may be best to contact a professional technician for further assistance.


What do you do when your washing machine is done a load of laundry but still full of water?

The pump may be bad or weak. You can check the small lid switch under the lid. When you close the lid...it will engage. These will sometimes get out of sinc with the lid and not engage.


Kenmore washing machine will fill with water and drain off but will not spin water out or wash?

If a Maytag washer fills with water but does not agitate it could a problem with the switch in the lid. There is a switch that locks the lid down during agitation and spinning. The magnet could be defective.


What did a washing machine look like in the 1920s?

1920's washing machines didn't have a lid. You would have to get the hose from the garden and fill the washer machine up!


What could be causing a washing machine to not ring the water out of clothes?

Possible causes for a washing machine not ringing out water from clothes could include a clogged drain pump, a malfunctioning lid switch, or a problem with the machine's motor or belt. It could also be due to imbalanced loads, which can prevent the machine from spinning properly.


Have model kaws750jqo machine fills and starts washing then quits when it should go to rinse and sometimes have to lift lid to start washer again?

There is a safety switch on all washers and dryers to stop accidents. It turns off power when the lid is raised. Most likely the switch needs adjustment if the machine goes into normal cycle when you lift the lid. Locate switch and adjust to make it less sensitive. First turn power off, remove plug.


Where is the serial number on a washing machine?

There should be a tag under the lid on the rim of the opening.


Why wont my Maytag washing machine spin?

There could be several reasons why your Maytag washing machine is not spinning. This could be due to a broken belt, a fault in the motor, a clogged drain pump, or an issue with the lid switch. It's best to consult a professional technician to diagnose and fix the problem.


How to fix lid switch on kitchen-aide washer?

If you are sure the lid safety switch is at fault do not bother with it, they are cheaper and easier to replace


What could be causing my Whirlpool washing machine's spin cycle to not work properly?

There are several possible reasons for a Whirlpool washing machine's spin cycle to not work properly. Some common causes include a broken or worn drive belt, a malfunctioning motor, a faulty lid switch, or an issue with the machine's control board. It is recommended to consult a professional technician to diagnose and repair the specific issue with your washing machine.