Glue and Adhesives

Yes, glue sticks can be melted by heating them to a high enough temperature using a heat gun, oven, or microwave. However, it is important to be cautious as the melted glue can be very hot and cause burns.

No, wood glue and white school glue are not the same. Wood glue is specifically designed for bonding wood surfaces together and is stronger and more durable than white school glue, which is typically used for arts and crafts projects.

Inhaling glue is often referred to as "glue sniffing" or "glue huffing." This practice is a form of substance abuse and can have serious health consequences.

When Super Glue is burned, it can release toxic fumes such as hydrogen cyanide and carbon monoxide. These gases can be harmful when inhaled and should be avoided by using the glue in a well-ventilated area and following safety guidelines.

Glue hardens when exposed to air due to a process called polymerization. When glue is squeezed from the tube, it comes in contact with air, leading to the evaporation of solvents or water present in the glue. This causes the glue molecules to come closer together and form a strong bond, resulting in hardening.

To remove sticky residue from glasses, you can use a mixture of warm water and gentle dish soap. Gently rub the affected area with the soapy water using a soft cloth or sponge. For stubborn residue, you can also try using a small amount of rubbing alcohol or white vinegar.

When glue is mixed with borax, a cross-linking reaction occurs between the polyvinyl acetate molecules in the glue and the borate ions in the borax. This creates a network of long chains that trap water molecules, giving slime its unique stretchy and gooey texture.

Try searching for Whirlpoo/Maytag Seal Adhesive. I found this on Ebay. Have not tried it yet, but have been searching for the same. I am going to try to find it locally, but if not will most likely order from ebay. It is listed for about $10

Maycor 055980 High temperature Adhesive.

The weight of hot glue can vary depending on the brand and type, but on average, a standard hot glue stick weighs around 7-10 grams.

Spray, or using an eyedropper, glue remover, through the lace unit on the hair side. Wait for wig to completely release! Don't pull it off! If needed, spray, or drip, remover between lace until and skin to ensure a clean release.

The melting point of solder is around 300 degrees C. The low melting point is the reason it is useful for soldering.
The melting point of solder will depend on what the solder of composed of. The most common solder has a melting point of 361.4 degrees F.

Styrofoam is made of polystyrene, which is a type of plastic that can be dissolved by certain chemicals found in glue. When glue comes into contact with styrofoam, it breaks down the polystyrene molecules, causing the material to melt or soften. The glue essentially eats away at the styrofoam, causing it to lose its shape and structure.

Swallowing nail glue can lead to stomach irritation, nausea, vomiting, and potential blockages if a large amount is ingested. It is important to seek medical help if nail glue is ingested to ensure proper treatment.

For glue to form a bond between two materials, the surfaces must be clean and free of dirt, oil, or other contaminants that can prevent proper adhesion. Additionally, the materials must be pressed together with sufficient pressure for the glue to set and form a strong bond.

Most glues are not meant to be ingested and can be toxic if swallowed in large amounts. It is important to read the safety instructions and warnings on the product packaging to understand the specific risks associated with the type of glue being used. If ingested or inhaled, it is recommended to seek medical advice immediately.

Boil a pot of water on a stove (but not to hot, it could ruin the cardboard). The steam from the boiling water should be able to moisten the adhesive. Then, take your nail and SLOWLY peel the adhesive, but test it on a corner first. Finish up and then clean any other minor residues (assuming that it is a project)

This is easy - Rub it gently with a rag and a few drops of Goof Off, then rinse it off, now spray with 'Shout' or a similar product, scrub gently for a minute or two then let it sit 10 minutes with the Shout in it before flinging into the washer for a warm wash.

Super glue can stain clothes by creating a strong bond with the fabric fibers, making it difficult to remove. The glue hardens quickly upon contact with the fabric, causing it to bond and become a permanent or difficult-to-remove stain. It is important to avoid getting super glue on clothes, as it can ruin the fabric.

The word adhesive as a noun could have the synonyms glue, paste, gum, or binder.

The adjective adhesive could have the synonyms sticky, gluey, gummed, or clinging.

1. Pressure-sensitive adhesives: These adhesives are tacky at room temperature and adhere to surfaces upon application of light pressure without the need for solvent, heat, or water.
2. Film adhesives: These adhesives come in the form of thin films or tapes that can be applied to surfaces through heat activation or pressure, creating a strong bond once cured.
3. Structural adhesives: These adhesives are designed to create durable bonds between substrates, often in industries like aerospace or automotive, and can be in the form of paste-like substances, films, or even threadlocking adhesives.

The sticky note is stick because the people who make the sticky note make it sticky on the back so they will stick to stuff like desk, walls, ect...

Depends on the application but rubber, before it sets, can fill in tiny spaces on the metal. As it sets it'll expand and grab onto those scratches, dents or any other type of texture.

Sometimes it's a chemical bonding.

Adhesive force is the attraction between molecules of different substances. It allows substances to stick together, such as water sticking to a glass surface. Adhesive force is important in processes like adhesion, where two different materials are held together.

There is one special glue that will conduct electricity. I can't remember the name, but it was an epoxy made to repair the rear window heating strips in cars in the '60's. - No other modern commonly available glues conduct.

Glue usually possess a "base" ph level. Bases have a ph level of 7.