Mazda

The fob must be gently pried apart, the electronics unit removed, the battery replaced, the electronics unit reinstalled, and the fob snapped back together. Your owner's manual should tell you how, if not ask your dealer.

Symptoms of a bad fuel pump in a Mazda 3 may include difficulty starting the engine, stalling while driving, and a loss of power during acceleration. You might also notice a decrease in fuel efficiency or unusual noises coming from the fuel tank. If the fuel pump fails completely, the engine may not start at all. It's important to address these issues promptly to avoid further damage.

Before you can fix it, you need to diagnose what the problem is. Have you checked fuses and relays? Do you have continuity in the high beam circuit on the switch? Is there power to the point where the wiring harness splits off to supply each high beam lamp? Have you checked the bulbs? There are several different reasons why your high beams could be malfunctioning... without narrowing down the cause, you'll just end up wasting money by throwing parts at it until you get it right (if you do at all).

No. Ford is a separate company from Mazda, owned by the Ford Motor Company, that currently only owns Lincoln and Mercury and previously owned Merkur. Mazda is only related to Ford by 45% of their vehicles, but they are not the same company. Mazda is also its own company.

There's been 5. All minor except accelerator/stuck throttle (2) different ones for this, search for more

The orifice tube on a Mazda B-3000 is typically located in the refrigerant line between the condenser and the evaporator. It is usually positioned near the firewall, close to the evaporator core. To access it, you may need to remove some components or insulation around the area for better visibility and reach. Always consult the vehicle's service manual for specific details and diagrams.

On a 2006 Mazda 6, the fuel filter is located within the fuel tank as part of the fuel pump assembly. This design means that accessing the fuel filter typically requires removing the fuel tank. It's recommended to consult the vehicle's service manual for detailed instructions if you need to replace or inspect the fuel filter.

To replace the headlight assembly on a 1998 Mazda 626, first, open the hood and detach the battery's negative terminal for safety. Remove the screws or clips securing the headlight assembly, then pull it forward gently to disconnect the wiring harness. After replacing the assembly, reconnect the wiring, secure it with screws or clips, and finally reconnect the battery terminal. Make sure to test the new headlight for proper function before closing the hood.

The oil sending unit on a 1998 Mazda B4000 is located on the engine block, typically near the oil filter. It is usually positioned towards the back of the engine, on the driver's side. To access it, you may need to remove some components for better visibility and reach. Make sure to disconnect the electrical connector before removing the unit.

Look on exhaust pipes, should have one on manifold for each bank and one aft of convertor, they monitor 02 in exhaust and adjust injectors, one aft of convertor monitors catylist function, will look like a spark plug screwed into a bung w/2 wires

The 1995 Mazda MX-3 with a manual 5-speed transmission typically requires about 2.4 quarts of transmission fluid. It's important to use the recommended type of fluid, usually a 75W-90 gear oil for manual transmissions. Always check the owner's manual or service guide for specific details and to ensure proper levels.

Is it possible an electrical problem can cause my engine coil to burn on my Mazda 323

If your Mazda 323 is burning the engine coil and struggling to go uphill, it could be due to several issues. A faulty ignition system, such as a short circuit or an overload from a malfunctioning coil or wiring, may cause excessive heat and damage. Additionally, poor fuel delivery or a clogged air intake could lead to engine performance problems, making it difficult to climb hills. It's advisable to have a mechanic diagnose the electrical and fuel systems to pinpoint the exact cause.

If you go to the Mazda web site it states Castrol motor oil is used.

To correctly place the distributor wires on a 1992 Mazda 323, start by identifying the firing order, which is 1-3-4-2. Connect the spark plug wire for cylinder 1 to the distributor cap terminal marked for cylinder 1, followed by cylinder 3, then 4, and finally 2, ensuring each wire is securely attached. The distributor rotates counterclockwise, so maintain that direction while connecting the wires. Always verify the connections against the vehicle's service manual for accuracy.

First step check fuel pressure with gauge at rail. Boost may work when you turn key but pump may be out.

My 1991 Mazda 323 has two plastic screws on drivers side, facing engine. Are they airbleeder valves?