Sewing

The cast of The Great British Sewing Bee - 2013 includes: Ingrid Benussi as Model Claudia Winkleman Claudia Winkleman as Herself - Host

There are 25.4 millimeters to an inch, so 18 millimeters would be approximately 3/4inch.

The 311 code can mean 2 things. It can mean that there is an encoder status that has not changed in 5 seconds. To fix this, check the line systems. It can also mean that there is a motor or belt failure.

Turn it so it is inside out. Or put them on inside out. You could try with pins or something, outline the pants until you get the right fit. then ... Take them off and sew where the pins were. Turn them the right side and you're done! OR Do lunges to get better legs and then youwont need too

I just paid $5.00 for my Reversew Electric Machine at a St. Vincent de Paul Store ( a type of Goodwill store). It looks neat and I can't wait to play with it. It has the Godzilla finish on it. I've never seen one before I found it today!

For sewing pattern layout, folds are made along the grain line. Lengthwise center fold would be folding the fabric with selvages together. Crosswise centerfold is folding the fabric at the crosswise grain, that is along the weft threads from selvage to selvage.

4' wide by 6' long

I found one selling on eBay and they were asking $45.99.

A great project if you have never sewn before is a pillow case. It will teach you the basics of using your machine, and help you practice sewing in a straight line, following a seam allowance, as well as teach you how to hem, which is an important skill when sewing any garment.

Check out the Lazy Girl Designs tutorial for some help getting started.

Good luck!

To much oil (if it's industrial) or broken oil seal on top crank shaft

Chances are if you search for CNC Lathe on ebay or Craigslist you'll be able to find out what you need. There are a variety of equipment available on these sites.

Adjust Elna SU machine as follows:

Set the stitch width knob and the stitch length dial at 0

If there is another Elna-disc in the automatic stitch control (called the elnagraph), remove it by pressing the button

Put the Elna-disc you want to use in the Elna graph with the circular mark over the driving pin and press the Elna disc down

For single elna discs:

Use embroidery and buttonhole foor for filled designs with raised effect and the sewing foot for linear stitches iwthout any raised effect.

1. After inserting the Elna-disc in the Elnagraph, and with the stitch width knob and the stitch length dial on "0", turn:

2. the selector to A (automatic)

3. the needle position to the centered position (red mark)

4. the stitch width knob with the straight mark on top to a position between 1 and 4, as desired

5. the stitch length dial to a position between 1/4 and 4, as desired

6. the stitch is then sewn automatically

7. Position the circle on the Elna-disc opposite the white arrow, by turning the flywheel; this shows the beginning and the end of each automatic stitch or design.

For double elna discs:

Use embroidery and buttonhole foor for filled designs with raised effect and the sewing foot for linear stitches iwthout any raised effect.

1. After inserting the Elna-disc in the Elnagraph, and with the stitch width knob and the stitch length dial on "0", turn:

2. the selector to A (automatic)

3. the needle position to the centered position (red mark)

4. the stitch width knob with the straight mark on top to a position between 1 and 4, as desired

5. the stitch length dial on A, as desired

6. the stitch is then sewn automatically

7. With the stitch length dial at A, the stitch length should normally be correct. However, for certain very intricate stitches (true hemstitiching with disc 101, 126, 140 or 142) sewn with double Elna-discs, it may be desirable to lengthen or shorten the pattern to adapt it better to the material and thread used.

8. If the stitch is too short ant A, turn the dial to "+".

9. If the stitch is too long a A, turn the dial to "-"

http://www.howtofashiondesign.com/DrawingDemo/GarmentDemo.aspx

Check out this helpful link it talks about thread tension, stitch plate, bobbin thread. You will have to get through the intro but then you will see

I don't have the answer, but my 420 does this all the time. I know it is a bobbin problem, but cannot figure it out. I reinsert the whole bobbin contraction over and over. I'm thinking of this useless machine myself!

In my opinion, always use 100% cotton. Very few people are allergic to cotton. Wool batting, or polyester can cause rashes.

Polyester batting will 'crumble' to granules and dust after a few years of repeated washing and abuse. Stick with cotton, especially for baby.

Something else to consider . . . If you are going to hand quilt the baby quilt, use a 'needled cotton batt.' It is easier to quilt. Also, it is a good idea to buy a cotton batting that does not contain little pieces of the 'hull' and seed ( some batts will have bits all through it. ) Those hulls and seeds will eventually bleed small amounts of cotton oil, leaving a stain on the quilt that will NOT wash out.

Because they are cool! And only the coolest people wear cool jeans!!! :)

The stitch selection panel is the function on a sewing machine that allows you to choose which stitch you want to sew: a straight stitch, zig-zag, embroidery stitch, etc.

If you are asking about Oil Cloth, it is not made from oil, it is a plastic covered cloth that repels oil.

There are fabric products made from petroleum products, but they are not made directly from oil.

call huffy parts department 1800-872-2453

One can purchase a Berina 830 sewing machine for a discounted price from Amazon, Overstock, or eBay. One can also order it from the Sewing Machines Plus website.

It is known as patchwork, often used to make a quilt for a bed.

some girls are fat it depends on the activitness and diet of the girl

they got paid 50 cents per day

Mary Anderson invented the windshield wiper.