Volume

There are approximately 2.4 cups in 500 grams of most dry ingredients like flour or sugar, but it can vary slightly depending on the ingredient.

The specific volume of saturated liquid water at 540 degrees Fahrenheit and 962.79 psia is approximately 0.0163 ft^3/lbm. The density of saturated liquid water at these conditions is approximately 61.32 lbm/ft^3.

About 5.91 inches. There are about 25.4 mm to an inch.

Direct Conversion Formula150 mm*1 in

25.4 mm=5.905511811 in

THERE ARE 4 QUARTS IN 1 GALLON, SO 8X4=32 QUARTS!

The patient may be preparing for a colonoscopy. The large volume of water helps cleanse the bowel for better visualization during the procedure.

1 liter is about 1.0567 quarts.

A 250 ml beaker is a laboratory glassware vessel that has a volume capacity of 250 milliliters. Beakers are commonly used for mixing, heating, and transferring liquids in scientific experiments. They are available in various sizes to accommodate different volumes of liquids.

65mL = 0.065L (Less than 1 Liter)

The conversion factor is 1000mL per 1 Liter.

The specific gravity is 1.326 @ 68 deg. F, so it weighs about 11 pounds per gallon.

Grams are mass, liters are volume. So it would depend on the substance.

Note ... with water (only) 1000 grams = 1 liter [by definition].

0.9kL equals 900000mL (@1 million mL per kL).

This is one of those questions that is best answered by trying it, but I will explain nonetheless. So here are your possibilities: 1. Dunk a sheet in water. The volume change here will be really small. A 1ft by 1ft sheet of aluminum foil will only have a volume of around 1.5 cm3. To get a piece of glassware big enough to accomodate the sheet will pretty much ensure that the precision is not sufficient to see a 1.5 mL volume change. 2. Wad up the aluminum foil into a ball. Just try this. TWad aluminum into a compact ball and measure its diameter. Assume a sphere and calculate its volume. Find its mass and divide to get the density. If you were really good about wadding up the ball you should get a density of between 1.5 and 2.0 g/mL---way lower than the actual value of 2.70 g/mL. Simply put---you can't exclude all the empty space. 3. The most accurate answer you can get is from repeatedly folding the aluminum until it is in a small compact shape, but even then you will end up short of the actual density when using water displacement because you can't remove all the air.

96 fluid ounces is 0.75 (3/4) gallon.

By unit of volume and conversion ,we can say that

1 gallon=16 cup

2 gallon =32 cup

1.35 US fluid ounces = 39.92 ml

4 quartos o 3.78 litros. U.S. gallons are different from imperial gallons. 1 Imperial gallon is equal to 4.54609188 litres and 1 US gallon is equal to 3.78541178 litres. Liters on the other hand are the same everywhere. One liter equals 0.26 U.S. gallon or 0.219 Imperial gallon.

3.75 gallons

1 Gallon = 8 pints

1 pint = 0.12 gallon

1 liter is 1000 milliliters.

1000 - 64 = 936 milliliters or .936 L

There are a lot of factors to take into account. First do not go by what fasion world says. If it was up to them we would all be sticks. If you are concerned then have your parents ask a doctor. Everybody is different.

That is approximately 0.882 cups.