0
97 Dodge Dakota heater core without disconnecting the AC accumulator?
Wiki User
∙ 14y ago
You will have to disconnect the liquid line and the accumulator from the evaporator tubes in order to remove the heater core.....
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace heater core on a 1997 dodge Dakota?
# Disconnect the battery negative cable. # Remove the instrument panel from the vehicle. # If equipped with air conditioning, recover the refrigerant. # Disconnect the liquid line refrigerant line fitting from the evaporator inlet tube. # Loosen the accumulator. # Dakota, Durango: disconnect the accumulator inlet tube. # Drain the cooling system. # Disconnect the heater hoses from the heater core tubes. # Remove the powertrain control module from the dash panel. Disconnecting wiring is not necessary. # Remove the four nuts from the heater-A/C mounting studs on the engine compartment side of the dash panel. # Remove the nut(s) that secure(s) the heater-A/C housing mounting brace to the stud(s) on the passenger compartment side of the dash board. # Pull the housing rearward far enough for the mounting studs and evaporator condensate drain tube to clear the dash panel holes. # Remove the housing from the vehicle. # Lift the heater core out of the housing. # Installation is the reverse of removal.
How do you replace heater core in a 1997 dodge Dakota?
# Disconnect the battery negative cable. # Remove the instrument panel from the vehicle. # If equipped with air conditioning, recover the refrigerant. # Disconnect the liquid line refrigerant line fitting from the evaporator inlet tube. # Loosen the accumulator. # Dakota, Durango: disconnect the accumulator inlet tube. # Drain the cooling system. # Disconnect the heater hoses from the heater core tubes. # Remove the powertrain control module from the dash panel. Disconnecting wiring is not necessary. # Remove the four nuts from the heater-A/C mounting studs on the engine compartment side of the dash panel. # Remove the nut(s) that secure(s) the heater-A/C housing mounting brace to the stud(s) on the passenger compartment side of the dash board. # Pull the housing rearward far enough for the mounting studs and evaporator condensate drain tube to clear the dash panel holes. # Remove the housing from the vehicle. # Lift the heater core out of the housing. # Installation is the reverse of removal.
Where is the heater core located in a 1991 Dodge Dakota?
The heater core on a Dodge Dakota is inside the HVAC housing, under the dash.
1988 Dakota heater core replacement?
To replace a 1988 Dakota heater core, first discharge the A/C. Then remove the lower instrument panel before removing the heater box unit.
Replace the heater core on a 2000 Dodge Dakota?
Disconnect the battery negative cable.Remove the instrument panel from the vehicle.If equipped with air conditioning, recover the refrigerant.Disconnect the liquid line refrigerant line fitting from the evaporator inlet tube.Remove the accumulator.Disconnect the accumulator inlet tube.Drain the cooling system.Disconnect the heater hoses from the heater core tubes.Remove the powertrain control module from the dash panel. Disconnecting wiring is not necessary.Remove the four nuts from the heater-A/C mounting studs on the engine compartment side of the dash panel.Remove the nut(s) that secure(s) the heater-A/C housing mounting brace to the stud(s) on the passenger compartment side of the dash board.Pull the housing rearward far enough for the mounting studs and evaporator condensate drain tube to clear the dash panel holes.Remove the housing from the vehicle.Lift the heater core out of the housing.
Where is the ac accumulator located on a 2000 ford explorer?
On the passenger side of the engine, not too far from the heater fan.
Mercury tracer heater core?
The Mercury Tracer heater core can be found behind the passenger side kick plate. The heater core can be removed by disconnecting the water supply lines and removing the retaining bolts.
Why with the heater on does the Chevy Impala blow cold air thru the driver side vent while hot air blows thru the passenger side vent?
you probably have a faulty drivers side temp door actuator OR The problem you have is the GM heater control unit has lost it's calibration, which can happen from time to time. The way to reset it is, start your car and turn your heater off, and shut off the car, pull out the keys. Then with vehicle off, disconnect the battery, (or batteries if two). Let sit for 10 minutes, then re-connect battery. Get in and start the engine, DON'T touch anything, let the heater control unit re-calibrate for at least 40 seconds, (by the clock), then try turning on the heater. Usually problem over, ! Note: make sure the radio is turned off before disconnecting the battery and if this does not solve the problem, chances are that the vent accumulator has gone bad. It's common for the gears in the accumulator to crack and seized, if your luck it's just to reset or just to lubricate the gears. Good luck Let sit for 10 minutes, then re-connect battery. Get in and start the engine, DON'T touch anything, let the heater control unit re-calibrate for at least 40 seconds, (by the clock), then try turning on the heater. Usually problem over, ! Note: make sure the radio is turned off before disconnecting the battery and if this does not solve the problem, chances are that the vent accumulator has gone bad. It's common for the gears in the accumulator to crack and seized, if your luck it's just to reset or just to lubricate the gears. Good luck
How do you replace a heater core in a 2000 Dakota?
You put a for sale sign on it!
Where is the heater fan rheostat located on a 2001 dodge Dakota?
The heater blower motor shouldn't have a rheostat, perhaps the resistor was meant? If so, it would be on the bottom of the passenger side dashboard, visible from the floor. There should be a 5-wire harness leading to it and it should be retained by two screws. Removal or replacement is as simple as disconnecting the harness, removing the 2 screws, and slipping out the module.
What is the location of the low pressure port on a 2000 Ford Explorer?
On the top of your air conditioning accumulator "can" covered with a plastic cap. You will find the accumulator on the passenger side of the engine, roughly 5 inches from your heater/air conditioning electric fan motor.
How do you replace heater core in 1999 ford f250 superduty?
The heater core on a 1999 Ford F250 Superduty is replaced by removing the heater hoses, disconnecting the wiring harness, and removing the retaining bolts. The cover can then be removed, the heater core unbolted, and removed from its housing.
