0
How do you remove ignition lock from 79 El camino column if you lost the key?
Wiki User
∙ 16y ago
Pull the steering wheel. Now be careful when you get to the wires and remember how to put it back together. There should be a button you can push to release the switch. It is about the size of a pin head. If that does not appeal to you I have drilled my ignitions out with a 1/2 inch drill. But if you go to far you can ruin the steering column. You dont want to go to deep no more than 3/4 inch. If you have another ignition look at it and see how far you can go. I then work at removing the metal til you can turn the ignition. It is just taking your time and not being in to big of a hurry. BE CAREFUL AND YOU SHOULD GET IT OUT OK AND BE ABLE TO DROP ANOTHER IGNITION RIGHT IN. Kathy
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you remove the ignition switch from a 1988 Dodge Ram 50?
Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.
How do you replace the ignition lock cylinder on a 2004 Honda civic?
The ignition lock switch is found under the steering column on a 2004 Honda Civic. Remove the steering column and ignition switch. Loosen the mounting screws that hold the cylinder in place. Pull and replace the lock cylinder.
How do you replace the ignition of a 1992 Lincoln Town Car?
To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.
How do you remove the steering lock on a 1994 Ford Probe?
# Disable airbag system. # Remove steering column covers and lower instrument panel cover # Lower steering column # Disconnect the shift interlock cable from ignition lock housing # The lock assembly is clamped to the steering column by two shear-head bolts. Drill heads off each bolt and remove the bracket. # Remove the steering lock assembly from the steering column
How do you remove the key from the lock ignition?
1996 rodeo- how to remove key from lock ignition?
Hoe to remove the ignition lock cylinder in a 99 cavalier?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
How do you remove ignition cylinder from 1988 Chevy pickup?
Remove the steering wheel. (you will need a steering wheel puller) Remove the turn signal switch. It is not necessary to completely remove the switch from the column. Pull the switch rearward far enough to slip it over the end of the shaft, but do not pull the harness out of the column. Turn the lock to Run. If necessary, remove the ignition key. If equipped, remove the buzzer switch assembly. Remove the lock retaining screw and remove the lock cylinder.
How do you replace a ignition lock cylinder in a 97 cavalier?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
How do you take the Ignition Lock Cylinder out of a 1996 Chevrolet Cavalier?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
How do you replace an ignition lock cylinder in a 1998 Chevy cavalier?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
How do you replace an ignition lock cylinder in a 1997 Chevy Cavalier?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
How do you replace the ignition lock cylinder on a Pontiac Sunfire 1996?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
