0
How do you remove the third brake light assembly on a 2002 Taurus?
Wiki User
∙ 13y ago
Raise wagon rear door hatch open. Grasp from the top edge the plastic molding around the glass and pull, but don't pull completely away. Be careful around the wiper motor housing and the pigtail for the window defrost. On the metal part of the window frame is a rubber plug in the center, pop this out to loosen and remove the top 10mm nut. The remaining(3) 10mm nuts are accessed thru openings in the metal window frame once the plastic molding is pulled back. Once you have all(4) nuts removed carefully push but don't connect plastic molding back towards frame so that you can lower and and close the rear hatch. Now you can remove the 3rd brake light housing from the outside and twist and remove light socket plug ins. Most Ford's use a L22 bulb. Double check your work, then install and tighten (4) 10mm nuts. To reinstall, be careful with the metal molding clips, notice one tongue goes up and the next clip the tongue goes down. Just massage the plastic window molding back into place using gentle up and down motion, make sure all (4) metal clips are secure.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you change the high mount brake lite on a 2007 Taurus?
The way that you change a high mount brake light on a 2007 Taurus is by first prying the light assembly from the housing. You then push rearward to remove it from the retaining clips. Next, life the light assembly from the shelf and disconnect the assembly wiring. Replace the light assembly and reverse directions to put the light housing back where it goes.
How do you replace brake light on Lexus RX300?
The brake light assembly can be access through the cargo compartment. Remove the cover to the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. The brake light will come out. Reverse the process to install the new brake light.
Center brake light replacement 2001 corolla?
The center brake light replacement will require replacing the entire brake light assembly. Remove the wiring harness. Remove the center brake light retaining screws. Reverse the process to install the new center brake light.
How do you remove third brake light s10?
Remove the two screws in the lens. You can remove the entire assembly once you do this.
How do you replace the brake light on a 2001 Jeep Cherokee?
To replace the brake light bulb you need to remove the whole light assembly. Once removed the change is simple.
How you you change the high mount brake light on 2001 Lexus RX300?
Remove the wiring harness from the high mount brake light. Remove the back cover of the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. Reverse the process to install the new brake light.
How do you disassemble the rear brake light cover so you can replace the brake light bulb on an '94 Mazda Truck?
You must remove the entire light assembly as follows: Lower the tail gate and remove the two small screws that screw into the side of the assembly. Next remove the two screws on the outside of the assembly that are accessible through long holes on the outside of the assembly. Pull the assembly back to expose the rear where the lights are located.
Change a Saturn L200 brake light?
If you want to change the brake light, you will need a Torx screwdriver. You will also have to open your trunk and remove the lens cover assembly.
Changing brake light bulb on a 2003 Toyota Tundra?
Open tailgate and you will find two bolts that hold brake/tail light assembly in place. Remove the two bolts and the assembly can be pulled out. Turn the brake light base counterclockwise a quarter turn, pull the bulb out directly, snap the new one in and then re-install the light assembly unit.
How do you replace a brake light on a 2003 Toyota RAV-4?
Open trunk and remove screws that secure light assembly to car. Pull assembly straight back to remove from car. Remove the dead light and replace with proper new light. Install in reverse order of removal.
Lexus LS400 brake light How do you replace?
You can access the brake light bald through the trunk compartment. Remove the trunk liner from the tail light assembly. Push the brake light connector in and turn at the same time. The brake lightbulb will come out. Reverse the process to install the new brake light
How do you change a 2004 Isuzu ascender back brake light?
Lift the hatch. Remove the screws in the tail light assembly. Pull the tail light assembly out. It may need a gentle nudge. Now untwist the bulb assembly socket counter clockwise to remove. Replace bulb. Re assembly is in the reverse order.
