0
How do you replace a rear glass window motor in a 2001 sport trac?
Wiki User
∙ 15y ago
Removal and Installation NOTE: The power rear window motor can be removed and a new one installed without removing the seat or trim panel. NOTE: When the power rear window motor is removed and installed, the motor must be initialized. For additional information, refer to Rear Window Motor Initialization in this section. # Fold down the passenger rear seat back. # Open the luggage compartment trim panel access door.
# Remove the spare tire jack and handle assembly.
# NOTE: The rear window glass water shield uses a reusable butyl rubber adhesive. A new water shield does not have to be installed unless it is damaged or if the butyl rubber adhesive does not adhere to a section of the sheet metal. Position the carpet aside and position the water shield back from the rear window glass motor to access bolts.
# CAUTION: Use care not to damage the drum housing when removing the rear window glass motor. NOTE: Apply pressure to the drum while removing the rear window motor to avoid extraction of the drum with the motor. Remove the rear window motor. ## Disconnect the electrical connector. ## Remove the bolts. ## Remove the rear window glass motor.
# NOTE: The rear window motor must be initialized after a repair is carried out. For additional information, refer to Rear Window Motor Initialization in this section. To install, reverse the removal procedure. (PASTED IN BELOW) == CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure. NOTE: The rear window motor is in error mode when shipped and will be inoperative until initialized. NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window glass module is installed, and any operation in which grease or lubricants are applied to the power rear window system. NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure. NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed. NOTE: Step 7 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the power rear window motor stalls the window into the upper header seal. Step 8 requires that the window control switch be momentarily turned to the OPEN position. NOTE: Step 9 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the window stalls into the upper header seal and the window carries out its down-up sequence, indicating successful completion of initialization. NOTE: The key-in-ignition chime can cause the vent button to be pressed more or less than six times due to the distraction of the chime. # NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes. Start with the ignition in the OFF position. Open the driver door.
# Turn the ignition to the ON position. # Press the power rear window control switch vent button six times.
# Turn the ignition to the OFF position. The driver door must be OPEN. # Press the power rear window control switch vent button six times.
# Turn the ignition to the ON position. The power rear window will move down-up-down-up approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialization mode. # Rotate and hold the power rear window control switch to the CLOSE position until the window stalls into the upper header seal.
# Momentarily rotate the power rear window control switch to the OPEN position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
# Rotate and hold the power rear window control switch to the CLOSE position. Continue to hold the switch until after the window stalls into the upper header seal and carries out the down-up movement. This down-up movement is approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
# Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions. If the window does not operate correctly, carefully repeat this procedure.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace a windshield wiper motor on a 1998 Mitsubishi mirage?
How to replace wiper motor on a 1998 montero sport mitsubishi
2001 jeep Cherokee sport passenger side window goes down but won't go up Put new motor in any suggestions?
did you also replace the regulator? sometimes its the regulator that goes bad and not the motor.
How do you replace the automatic window motor and regulator for the drivers side window on a 1994 Jeep Cherokee Sport?
Remove the door panel. Remove the bolt that fastens the regulator to the window. Remove the 3 bolts that hold the regulator assembly to the door. Squeeze the entire assembly through the largest hole and replace with a new assembly in reverse order.
How do you replace a window by yourself in a 1997 ford escort sport?
You take the inner door panel off. Then, there is an arm that goes up and down called the window regulator. The glass is held in by hardware on the end of the regulator. If you get a used window from the salvage yard they will be able to tell you how to put it back in. Most of the time the window is separated from the regulator and the new window dropped in from the outside when the control handle is in the down position.
How do you get into Astra Sport when keys locked inside?
Break the window , start car with the keys and drive to your nearest glass shop .
What else could cause a 2001 Ford Sport trac rear window to not close beside the motor?
if the motor is turning then it could be off the track or a gear might be stripped.
If a Drivers side electric window on a 2002 dodge caravan sport won't go up or down what could be wrong?
the window motor could be busted or a fuse could have blown.
How do you remove the lift gate trim panel on a 2001 Ford Explorer Sport to replace the rear wiper motor?
you have to remove the 2 brackets of the rear panel situated where the rear window close, then take the rear panel up, that's all
When was Glass Sport Motors created?
Glass Sport Motors was created in 1958.
How do you replace a Sport trac rear window motor?
How to replace the rear window motor on a 2001 Sport Trac: 1. fold down the rear seats. 2. flip up and remove the spring-loaded hinge on the cargo platform by removing the philips-headed screws. 3. remove the plastic fasteners for the rear plastic body panel. 4. pry the plastic rear body panel from the tabs at the top (left and right). 5. remove the two plastic felt fasteners. 6. peel down the motor cover located behind the rear right seat. 7. remove the 3 torx bolts on the motor. 8. using a large screwdriver or small pry bar, pry the motor away from the cable spool, leaving the spool intact on its mount. 9. unplug the motor and remove. 10. using a screwdriver, rotate the spool to give it some play (the window should move some). 11. put a dab of grease on the motor hub. 12. install the new motor by aligning the hub splines and rotating the motor into position. tighten the torx bolts. 13. Reassemble everything. 14. Initialize the new motor: open door, turn key to 'on', push rear window button 6 times, turn key to 'off', push rear window button 6 times, turn button right until window closes all the way, turn button left until window opens all the way.
Why is your blower only works on the highest setting on your 2001 Dodge Durango Sport?
You need to replace blower motor resistor.
What is the process in replacing the front drivers side power window regulator on a 98 Jeep Cherokee Sport. Where can you find these parts?
I AM GOING THROUGH THIS MYSELF. i HAVE LOCATED THE PART ON WWW.ROCKAUTO.COM (DORMAN PART # 74168) FOR 77.70 FOR THE MOTOR AND REGULATOR. i WILL POST MORE ONCE i REPLACE IT.
