0
yes
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you repair a fuel gauge in cavalier?
if your fuel guage is not working properly it is more than likely your fuel level sending unit which is in the gas tank of your vehicle, to repair, yo must purchase a new sending unit, drop the tank down and out of your car, by disconnecting the fuel and evap lines along with the filler neck and vent tube, and last the 2 bolts holding the straps, then replace the sending unit and bolt it all back together
Where is the fuel pump on 1996 ford e 250?
The fuel pump is in the fuel tank. Take the nuts off the tank starps. Drop the tank. Remove the fuel and vent lines. Knock the retaining ring off the pump and sending unit on the top and pull it out. Reverse procedure for installation.
How do you change a fuel pump in an 1996 Chevy Corsica?
the vehicles fuel tank must be removed. There are two 15mm bolts holding the fuel tank straps to the car. There are three fuel lines attached to the fuel tank sending unit, a feed line, a return line, and a vapor line. There are also two large hoses for the filler neck, the filler itself and the filler vent. It is recommended that you get help to lower the fuel tank down if it is more than a quarter of a tank full. Once down, remove the lock ring holding the sending unit in the tank. From this point, the fuel pump is visible. Installation is reverse of removal.
What will a fuel tank clogged vent do?
The engine Will struggle to get fuel.
How do you replace a fuel pump on a 1995 Chevy silveroado ext cab?
you are going to have to drop the tank.... place a jack under the gas tank to support it while removing the two tank straps, once removed lower the fuel tank and remove the fill & vent hose's, fuel lines, and electric harness. now just remove the sending unit from the tank. now all you have to do is take out the old fuel pump and replace it then put it all back together shouldn't take more than a few hours...
Where is Fuel Tank Vent Valve on kia sorento 2003?
The 'vent valve' is a breather... it has no moving parts... they're typically placed at the top of the fuel tank.
How do you replace a fuel pump on a 1999 Dodge Ram 1500 pickup?
start by draining gas tank then jack truck up don't forget to trig wheels, remove straps that hold gas tank to chassey, use penatration oil on bolts, disconnect filler hose and vent hose lower tank disconnect fuel lines and wiring, remove tank from under truck now you will have to remove sending unit from gas tank that is where you will find fuel pump unscrew old pump, install new pump. Replace everything same way you took apart.{p.s. becarfull not to damage locking ring that holds sending unit in place
How do you remove the fuel pump on a 1988 Landcruiser FJ 62?
You have to remove the fuel tank. First, remove the spare tire and the cross member bolted to the frame below the fuel tank. Next remove the swaybar end- link brackets that are bolted to the frame, as the fuel tank will not clear them on the way out. Drain the tank of fuel, there is a 17mm plug on the bottom of the tank. Disconnect all of the vent lines @ the right rear quarter next to the fuel filler hose, and the filler hose as well. The two lines at the front of the tank go to the fuel sending unit and you must be extremely careful when removing the rubber hoses from the lines. A new assembly is near impossible to find. Once all the lines have been disconnected, support the tank and remove the straps that hold it in place. There is plenty of slack in the wiring to the level sending unit and the fuel pump, so you should be able to hang the tank down a few feet to disconnect them. You might need a prybar to coax the tank out.
How do you remove and install a gas tank on a 91 s10 Blazer?
See if this helps. 1. Remove fuel from your gas tank. 2. Take off clamp to filler hose and disconnect filler hose and vent line. 3. Remove fuel tank retaining straps and support tank with a jack. 4. Lower fuel tank with jack to disconnect sending unit wires, hoses, and ground strap. 5. Carefully remove fuel tank from vehicle. 6. Take out fuel pump. Use brass punch and hammer for retaining ring. Reverse the above procedure for installation.
How do you change a fuel pump on a 92 Pontiac Sunbird?
you have to empty the fuel first.2 relieve the fuel system pressure on fuel injected model. 3 detach cable from - battery cable 4 raise vehicle and place on jackstands 5 locate electrical connector for electric fuel pump and fuel gauge sending unit in front of the tank, and unplug it. If no connector refer to step (9) 6 disconnect fuel feed and return lines, the vapor return lines, and the filler neck and vent tubes 7 support the fuel tank with floor jack 8 disconnect the wires and ground strap from the fuel pump/fuel gauge sending unit if you haven't already 10 remove tank from vehicle 11 installation in reverse of uninstall
How do you change the fuel pump in a 1992 full size blazer?
if it is fuel injected 1 empty fuel 2 drop fuel tank and remove filler tube and vent tube via hose clamps 3 detatch fuel lines from sending unit located on top of tank(if possible) 4 there is a cam lock ring that you need to use a flathead screwdriver and a hammer to tap it counter clockwise to release it from the tank 5 pull sending unit and fuel pump out of tank while being careful to not break off the gas gage float. replace fuel pump and strainer. check wires to check for damage. 6 connect fuel pump and turn key on to check if it kicks on. 7 put it all back together. need 2 people. approx 2 hours
How do you replace fuel pump in 1989 cutlass supreme 2.8L?
Best thing to do is take the car to a garage to have it done. Yes it will cost a bit (about $500) but it will save you all the head aches of trying to get the car up high enough to remove the fuel tank. If you want to do it yourself then follow this procedure. Drain fuel from tank. Relieve pressure from fuel system. Disconnect battery. Raise car and support safely. Disconnect filler tube from tank. Disconnect line going from tank to fuel filter. Disconnect fuel return line at braided hose. Disconnect vapor purge line at front of tank. Lower exhaust from rubber hangers. Remove the heat shields. Disconnect the electrical connector going to sending unit. Support tank and remove bolts holding tank straps. Lower tank to disconnect wiring harness. Remove vent hose from sending unit. Disconnect vapor purge hose from vapor tube. Remove tank. Once out turn the lock ring counter clockwise (screw driver and hammer work best). Lift fuel pump sending unit out of tank. Slide pump up to remove from pulsator then down to remove. Reverse to install.
