0
What size socket should be used to remove a 1994 corolla front hub bearing?
Wiki User
∙ 11y ago
For Axle Nut its 30mm
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What size socket do you use to replace a wheel bearing on a 2006 cobalt?
you do not use a socket you use a wheel bearing puller to remove it from the hub Putting a right size socket into it and hitting it with a hammer can pop the bearing out, but it can also damage it so its advised to get the right tools. size 30 mm for the wheel nut and the bearing puller
Where is the diagnostics socket on your Toyota Corolla?
The diagnostics socket on a Toyota Corolla can be found inside the car. It is next to the hood release.
What size socket is needed to remove the rear hub bearing nut on a 2000 dodge stratus?
30mm
How do you remove the rotor on 1991 Ford F150 4X4?
special socket required to remove nut that retains rotor and wheel bearing. use impact gun . be prepared to repack and reset wheel bearing
How do you change rotors on a ford f 250 heavy duty pickup 4x4 5.8 liter?
Remove Wheels Remove center hub Probably spring loaded Remove gear (Should slide out) Remove spanner nut with spanner socket Remove brake caliper and support Wiggle rotor bearing should fall out Remove rotor
How can you get the right rear hub off a 91 Dodge Colt?
It is probably held on with the bearing retainer nut.Remove the nut, washers, and bearing, and it should come off.The bearing retainer, or "spindle" nut, usually requires a 30mm socket to remove. If you can borrow an impact wrench (an electric model works well), the procedure will be much easier.
What size socket for a Toyota Corolla spark pulg?
16mm
How do you install front wheel bearings on 2001 Oldsmobile silhouette?
Remove tire, install spare which has an open center hole allowing access to axle nut, remove axle nut (33mm socket), remove spare, remove caliper, remove rotor, remove hub/bearing assembly, install new hub/bearing assembly, and so on in reverse order.
What size socket is required to remove the main nut from the end of your 89 Corsicas driveshafts?
It should be a 36mm socket.
How do you replace a rear wheel bearing on a 2000 Chrysler neon?
It's simpler then it looks. Remove the wheel then the brake drum, with a flat head screw driver remove the dust cover. you will need a large socket to remove the nut. I bought one at Auto Zone I beliieve it was a 36MM but the package says earley Chrysler Front hub nut socket (same nut for the rear) after removing the nut the hub and bearing asy will slide off. When putting on the new hub make sure you grease it with bearing grease
How do you replace left front rotor 1992 F1504x4 cannot disassemble bearings to remove rotor?
to dissasemble wheel bearings you need a special socket after you remove 4x4 hub this special socket will only fit the front bearing nut .a different size is used on the rear
How do you replace an U-Joint?
U-Joint OverhaulExcept Double Cardan Universal # Remove the driveshaft from the vehicle and place it in a vise, being careful not to damage it. # Remove the snaprings, which retain the bearings in the flange and in the driveshaft. # Remove the driveshaft tube from the vise and position the U-joint in the vise with a socket smaller than the bearing can on one side and a socket larger than the bearing cap on the other side. # Slowly tighten the jaws of the vise so that the smaller socket forces the U-joint spider and the opposite bearing into the large socket. # Remove the other side of the spider in the same manner (if applicable) and remove the spider assembly from the driveshaft. Discard the spider assemblies. # Clean all foreign matter from the yoke areas at the end of the driveshaft (s). # Start the new spider and one of the bearing cap assemblies into a yoke by positioning the yoke in a vise with the spider positioned in place with one of the bearing cap assemble positioned over one of the holes in the yoke. Slowly close the vise, pressing the bearing cap assembly in the yoke. Press the cap in far enough so that the retaining snapring can be installed. Used the smaller socket to recess the bearing cap. # Open the vise and position the opposite bearing cap assembly over the proper hole in the yoke with the socket that is smaller than the diameter of the bearing cap located on the cap. Slowly close the vise, pressing the bearing cap into the hole in the yoke with the socket. Make sure that the spider assembly is in line with the bearing cap in far enough so that the retaining snapring cap in far enough so that the retaining snapring can be installed. # Install all remaining U-joint in the same manner. Install the driveshaft and grease the new U-joints.
