0
94 Chevy s 10 pick up with a 22 size motor you went to start it one day and all you heard was a click so you put a starter in it and it still just clicks?
Wiki User
∙ 18y ago
if you have a moveable pole starter the solenoid is not attached to it therefore the problem could be a shorted starter solenoid.it could also be a bad ground to the solenoid.if you remove the starter again bench tested first to make sure it works.(it will save you time) just connect a battery to it.(make sure that + and - are in the right place .)also check your battery connections
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
Why is your 1995 Toyota 4-runner not turning over with a good battery?
Do you have any click in the starter itself but still not turning over? Then its the starter giving you fits. Replace it. If no click is heard then it could be a fuse or more likely the starter relay. Check them both before moving to the starter.
How do you know if your starter is going bad?
One indication that the starter is going bad in your vehicle is if the vehicle won't start but the battery is full of life. When the starter is the reason, a very audible click will be heard.
Can't start 87' El Camino. was fine yesterday heard it could be neutral safety lockout but the headlights go dim when you turn the key is it the starter?
Starter, or motor is locked,,, Turn the motor somehow, listen for A click, if you hear it the starter was jammed, It should start, If you turn the motor and you do not hear A click try it anyway if it still will not try to start it is likely the starter
How can I tell whether my starter of flywheel is bad on my 94 Nissan Pathfinder?
if the starter is bad you will hear one single click, if the flywheel is bad it will sound like a heard of daemons are trying to exit from under your vehicle. if its your flywheel you will know what i mean by the comparison
You tried to start your dodge ram this morning and only heard a click then seconds later a fizzle followed by smoke from under the hood Should you just assume its the starter and replace it?
Probably Not.
Why does maytag neptune dryer lights up turns on you push start and it clicks once and doesnt work you opened the top and heard the click louder coming from around the circuitboard Any ideas?
The timer is probably bad, if it won't advance the cycle will not start.
Is there any dual star delta starter?
Nope .. Never heard of it .
How do you know if you joint is bad?
You can run a quick diagnostic test on it as follows: 1)Get in your car 2) Make sure you have a lot of room 3) Put your car in Reverse 4) Accelerate Slowly 5)Crank the wheel to the right 6)Listen for "CLICKS" 7)Crank wheel to left 8) Listen for "CLICKS" If you heard clicks you should have been able to tell which side of the car it came from but if you heard clicks while cranked right you should have heard it come from the left side, and vice versa. If you hear clicks you should think about getting it replaced soon, if it goes unchecked you could have some more severe consequences. They tend to run $75-150 and if you are mechanically inclined at all it is rather easy to replace it yourself!
How do you get a Sinnoh starter in soul silver?
trade with someone That appears to be true. Professor Elm will give you 1 Johto Starter Steven will give you 1 Hoenn Starter, and Professor Oak will give you 1 Kanto Starter I have not heard anything about a Sinnoh Starter.
What does herd mean in slang?
Heard. Example: I herd u liek mudkipz = I Heard you are quite partial to the liking of a starter water based pokemon.
Is there a differEnce between manual and automatic starter on1989 Mazda 626 4 cylinder?
I have never heard of an Automatic Starter. Are you talking about a Remote Starter? Now if you are asking if an A/T equipped Mazda and a Manual Transmission equipped Mazda have the same starter, the answer is yes, they are identical.
What are some tips for replacing a starter on a 1995 Chevy blazer I have plenty of mechanical experience but I heard the shimming process is difficult?
When you get the new starter bolted on, pry the starter drive out to mesh with the ring gear. There should be some backlash between the teeth. If it's too tight, remove the outer bolt and loosen the inner bolt, and put a shim in. Reinstall the bolts and check for backlash again. Usually one shim is enough, but sometimes you need two.
