0
A 3.0 lamp and a 6.0 lamp are connected in serieswhat is the total resistance of the combination?
Wiki User
∙ 13y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
You are just asking that let us assume you have connected 2 or 3 resistors in a circuit and the current flowing through the circuit and from all the resistors will be same but how?
If the resistors are connected in series, the total resistance will be the sum of the resistances of each resistor, and the current flow will be the same thru all of them. if the resistors are connected in parallel, then the current thru each resistor would depend on the resistance of that resistor, the total resistance would be the inverse of the sum of the inverses of the resistance of each resistor. Total current would depend on the voltage and the total resistance
How much resistance must be connected in series with a 250 ohms inductive reactance to produce a total ciruit impedance of 400 ohms?
how much resistance must be connected in series with a 250 ohms inductive reactance to produce a total ciruit impedance of 400 ohms?
How do you connect a voltmeter in parallel circuit?
A voltmeter is used to measure potential difference across two points in an electrical circuit . The voltmeter is connected in parallel across the circuit element (resistance ) so that its inclusion in the circuit has negligible effect on total resistance and current flowing in yhe circuit A voltmeter has high resistance,if connected in series it will increase of circuit and reduce the current in the circuit
What is the unit of measurement in calculating the ship total resistance?
resistance will be in newtons, this force is linked to the square of the velocity, ie if you go twice as fast you' ll encounter four times the resistance
Placing a voltmeter into a circuit will raise the circuit resistance?
Usually a volt meter is placed across a component to measure the voltage drop across that component. Doing this places the volt meter resistance in parallel with that component's resistance, which will always lower the total resistance. Since the volt meter resistance is usually very large relative to the resistance of the element being measured, the total resistance does not change significantly. The formula for total resistance of two parallel elements is: Rtot = (R1*R2)/(R1+R2), as R1 (the volt meter) >> R2, Rtot ~= (R1*R2) / (R1) = R2 If a volt meter is placed into a circuit instead of around an element of that circuit, it will raise the resistance of the circuit, load the circuit with, and interrupt "normal" operation of the circuit (normal operation = how things would be without the meter in place). More importantly, the volt meter would then be measuring the voltage developped across itself (instead of an element of the circuit), which is not the point of this tool / this would be a misapplication of a volt meter.
What is the total resistance is V is 10 volts R1 is 1000 ohms and R2 is 1000 Ohms?
If they're connected in series the total resistance is 2000 ohms. If they're connected in parallel the resistance is 500 ohms.
When 2 resistors are connected in parallel r1r2 are?
Two resistors connected in parallel are 1/2 the sum of their resistance. The resistance of two resistors connected in series is the sum of their resistance. For example: The total resistance of a 100 ohm resistor connected to a 200 ohm resistor in parallel is 100+200 divided by 2 = 150 ohms. The total resistance of a 100 ohm resistor connected to a 200 ohm resistor in series 100+200= 300 ohms.
What is Resistance of 20 ohms and 10 ohms?
Well, the total circuit resistance depends on the type of connection. If the two resistances (or any number of resistances) are connected in series, IE. one resistance end is connected to one end of another resistance, the the circuit total resistance is the sum of the two resistances. say two resistances r1 and r2 are connected in series the total resistance is r1+r2 (in this case its 30 ohms). If the resistances are connected in parallel IE. both the ends of a resistance are connected to both ends of another resistance then the total resistance in this case shall be (r1*r2)/(r1+r2) ,( that is 6.67 ohms in given case).
What is the rule for finding the total resistance of a number of resistors connected in series?
If the resistors are in series, then the total resistance is simply the sum of the resistances of each resistor.
A 80 ohm resistor is connected in parallel with another 80 ohm resistorwhat should be the total resistance?
The total resistance would be 40 ohm.
You are just asking that let us assume you have connected 2 or 3 resistors in a circuit and the current flowing through the circuit and from all the resistors will be same but how?
If the resistors are connected in series, the total resistance will be the sum of the resistances of each resistor, and the current flow will be the same thru all of them. if the resistors are connected in parallel, then the current thru each resistor would depend on the resistance of that resistor, the total resistance would be the inverse of the sum of the inverses of the resistance of each resistor. Total current would depend on the voltage and the total resistance
How do you find resistance in a parallel circuit?
resistance inparallel decrease in value proportionally two resistance can be calculated as R1XR2/SUM OF R1+R2. many values can be calculated as a fraction 1/r+1/r2+1/3 ....and take the total sum reciprocal
What is the relationship between total resistance and the resistance across each load?
There is no such thing as 'resistance across' a load! The correct term is 'resistance of a load'.To answer your question, it depends on how the loads are connected. If they are connected in series, for example, the total resistance is equal to the sum of the individual resistances. If they are connected in parallel, then you must use the following equation: 1/R = 1/R1 + 1/R2 + 1/R3 + etc.For any other connection, you will have to work it out individually.
What is the total resistance of 15 ohms?
That depends how they are connected. For example, if they are connected in series, just add the individual resistances.
How are resistor connected in series?
when we want maximum resistance they are connected in series. when resistors are connected in series total resistance is maximum when resistors are connected in parallel total resistance is minimum for series total R=R1+R2+R3......... for parallel R1 in parallel to R2 total 1/R=(1/R1)+(1/R2) ie R=(R1*R2)/(R1+R2)
What is the total resistance of a circuit that contains two 100 resistors connected in paralle?
50 ohms
What is the total resistance in a circuit that contains three 60 resistors connected in series?
The total effective resistance of resistors in series is the sum of the individual resistances.Three 60-ohm resistors in series have a total effective resistance of (60 + 60 + 60) = 180 ohms.
