answersLogoWhite

0


Best Answer

try this for size...to not back up out of the drive way of a car wash and bang out! Meanwhile, thinking that you were preventing a accident that may have occurred.

User Avatar

Wiki User

โˆ™ 2008-03-21 19:53:43
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Approximately how much would a garage charge to fix a crank shaft bearing for a 1996 Chevy Lumina?
Write your answer...
Submit
Related questions

How much does it cost to replace the front wheel bearing on a Mazda 6?

a garage is probably going to charge you 2 hours of labor plus the parts


How do you change lower ball joints on a 1994 lumina?

Drive it to the local garage and pay to have it done.


Backup lights on 1995 Chevy lumina not working no power in the wiring what can I do to fix it?

Take it to the garage.


How much can a garage charge for storage after they finish repairs?

How much can a garage charge for storage after they finish repairs? in san bernardino county


What is tha avg charge for labor in a garage?

between $65 to $75 an hour


How would you fix the power steering in a '92 Chevy Lumina if it cuts out when you drive slowly?

HeyDuffman==If the belt is tight and it is full of fluid, take it to a garage. GoodluckJoe


Is it safe to drive with a bad wheel bearing?

Not knowing how bad the bearing is, I can't say how long it will last before the wheel falls off. Drive to your local garage for repair and don't take the highway.


How do you replace rear axle bearing on Subaru Forester?

This is a big job requiring the use of a press to remove and install the bearing. I have done this in my own garage, taking the hub out to a local garage for the press work. However, since you are asking here, you should have the whole job done by a mechanic that you trust. It is a big job. --Ken


How do i remove a Front wheel bearing on a Citoren 2cv?

as with all front bearings on any car it is usually easiar to remove the hub by undoing the ball joint ,trackrod end and usaully suspension off the hub but i would imagine that the bearing has to be pressed so the hub will have to be taken to a garage or someone with a bearing press so if you are not mechanically minded i would take the car straight to a garage and save yourself alot of hardwork.


1995 Chevy Lumina Do these cars have problems with rear suspension mine sounds horrible even after new struts and mounts replaced Please Help?

I have the same problem with my 93 Chevy Lumina. Was told by the garage I needed new buschings. Don't know if this helps....Good Luck!


How do you replace the wheel bearing on a Toyota Echo?

I had to pressed in by a garage . they did not last . I bought 2 from a junk yard no problems after 110k more miles i


How much garage charge should be if customer laying is vehicle at workshop without repairing?

It varies. I've seen $25 a day up to $150 a day. I think it depends on who owns the garage, state law and storage space on the garage's property.


Why is the clutch on my 2006 Nissan Sentra make a loud screeeching noise when i press the clutch in?

The throw-out bearing is toast. Don't drive it anywhere but to a local garage for repair.


Where can one buy a garage door insulation kit?

A person can buy a garage door insulation kit through Ebay. Energy Efficient Solutions makes garage door insulation kits. The price of a garage door insulation kit is approximately $90.00. These kits are also made by a company known as Atlas EPS.


How much should a garage charge to fit an f18 gearbox?

A lot. Between $1,000-$5,000 if they know how to.


How do you replace front wheel hub bearing 1991 topaz?

If you do not have the proper tool's, then it is really best to take the car to your local garage. This is a specific job.


How much does grease monkey charge to change sparkplugs in a 1996 Chrysler sebring convertable v6 motor?

hoW much does grease monkey garage charge to change spark plugs


What is the average cost of a garage door if purchased from garage doors of Indianapolis?

If you plan on doing self installs with the doors you should plan to spend about $280-$550 per door at Garage Doors of Indianapolis, Inc. An average cost per door would be approximately $415. Budgeting a minimum of $2,000 for a project with five unique garage doors would be wise.


How much does it cost to install an engine?

a do it your self will cost about $45 to do it right. a garage will charge between $750-$1200


What is the procedure for charging the air condition?

Unless you have a machine to do it and are trained to do it then never charge it. Take it to a garage and have them do it. Much safer.


How do you charge refrigerant airconditioner?

go to local repair garage (£25-£50) or halfords will re-gas for £50


How can you siphon gas out of a 95 Chevy Lumina?

Visit a garage. They may have a pump that will siphon fuel. Most vehicle fuel tanks have filters & screens that prevent the tanks from being siphoned with a hose.


How do you charge ac on 1995 Isuzu Trooper?

You can buy a charge kit from your local auto parts store and follow directions but if it needs a charge it must have a leak. Have the leak repaired first. This is best done by a garage that does AC work.


How much to replace the front wheel bearings in a 94 vw golf driver?

just had a 93 golf cl front wheel bearing done at a garage all in £110.00 had a rear bearing done through my works workshop and the bearing cost £11.21 half an hour to do, gave the mechanic £20 i am not sure but i think the front bearing is the same and to dissasemble the front takes a bit longer but not 3 hours


I am looking to paint my garage floor and would like to know approximately how much garage floor coating would cost me for a 20 X 20 garage.?

That should take less than a gallon. In general a gallon of epoxy coating is good for 500 square feet. A 20 *20 garage is 400 square feet so that's going to take less.

Study guides

๐Ÿ““
Create a Study Guide