0
Bleeder valve for coolant is broke how do you bleed air out of system?
Wiki User
∙ 15y ago
Replace the bleeder valve. On vehicles equipped with a bleeder valve it is imperative you use the bleeder to remove trapped air. No other procedure will remove all the trapped air. On cars without a bleeder, you simply remove the radiator cap and start the engine. Watch until all air bubbles have escaped. This will not be sufficient on your car. Failure to remove all trapped air, will lead to a hot spot and possible engine damage.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you bleed engine coolant if one bleeder is broke?
well, if there are two bleeders at the same level, the one that works will suffice, at a lower empty rate. If there is no second bleeder, use a small diameter siphon, or remove the lower hose from the radiator.
Where is the clutch bleeder on a 95 jeep wrangler the master cylinder broke you replaced it and cant find the bleeder screw it is not on the slave cylinder?
== == == ==
What is the cooling system capacity of a tractor trailer?
Twelve gallons, which is how many gallons I had to put in when my water pump broke and drained all the coolant on the road.
There is not a bleeder valve located anywhere on the clutch slave cylinder of a 95 v-6 firebird and the bleeder is not broke off even on the brand new part What is the bleeding procedure?
usaully when there isn't a bleeder on the value its consider a closed system a it needs the entire unit to be replace like on alot of the fords.... if it has a steel line going to it and not a plastic one you still might be able to bleed it... first fill the master up then open the line and wait till fluid comes out and close the line then pump the pedal and hold pressure on the pedal and while doing that have some one open the line till the pedal goes down almost to the floor and close the line and then repeat ....plastic system they sell as a complete unit slave, line and master cylinder hope i helped
Why would coolant in a 1999 jeep wrangler have a dark brown color?
The coolant is old, broke down, and needs replaced.
When should the coolant tank be replaced?
When it leaks. If it ain't broke don't mend it
My 98 Ford Taurus cooling system broke how much will it cost to get it repair and how come you cant drive with out it?
The cost to fix the coolant system depends on what is broken. It could be less than $100 for a hose to over $1000 for a head gasket. You cannot run the car without coolant because the engine would overheat and seize up.
What would happen if radiator hose broke on the impala?
you would lose all your coolant
Hown the left side the bleeder boltonthe caliper is broke can you get out?
to remove the broken bleeder. u can use an easyout most times you can get at this without taking calipre completely off car the bleeder already has a hole thru the centre, so all u need is to get correct size easy out the easy out screws into the hole that is already in the bleeder it will screw in backwards(left hand thread) while screwing in, it will cut into bleeder making its own thread when the easyout has good enuff contact the bleeder should screw out as you keep turning you will also need to be careful doing this as easy outs can break fairly easy if not comfortable, take calipre off vehicle and take it to a brake shop . a mechanic there can remove it for you NOTE do not let anyone tell you it cannot be removed you can also drill the hole a little larger before you start and use a larger easy out you will need to remove calipre from vehicle to do this and make sure that you flush out any metal debri from calipre before you reinstall if this works then you just install new bleeder into calipre ,then bleed your brakes
Where are the rear bleeder's located on an 86 cutlass supreme?
If by "rear bleeders" you mean the wheel cylinder brake fluid bleeder valve for the brake system look behind the backing plate (that's the part that has the brake shoe's attached to it). Jack you car up & support it with jack stands crawl under the car at the rear end look on top of the rear end housing & you'll see the brake lines that run to the wheel brake cylinders. Usually just above where they attach to the wheel cylinder is the bleed screw. Be warned if the cars that old spray some penetrating oil on them (W-D40) and wait for a little while... I've broke off my share.
How do you know if water pump has broke on my car?
You should see the coolant circulating in the radiator when the car is running
What did the assembly do to the court system?
It broke them.
